1. SAFETY INSTRUCTIONS
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1.2
GENERAL SAFETY
Familiarise yourself with the application, limitations and potential hazards of the machine.
WARNING!
Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to.
WARNING!
Disconnect from the mains power supply before changing accessories, servicing or performing any maintenance.
WARNING! DO NOT
sand any materials containing asbestos.
Maintain the machine and keep in good condition (use an authorised service agent).
Check the alignment of moving parts regularly. For safest performance keep the machine clean at all times.
Before each use check all abrasive attachments for condition. If worn or damaged replace immediately.
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts are dangerous and will invalidate the warranty.
Locate the machine in a suitable area. Keep area clean, uncluttered and ensure there is adequate lighting.
Ensure the machine is situated on a solid work surface, adequate for supporting the weight of the machine and the workpiece.
Ensure there are no flammable or combustible materials near the work area.
Remove ill fitting clothing, ties and loose jewellery, and tie back long hair.
Maintain correct balance and footing, ensure the floor is not slippery and wear non-slip shoes.
Keep hands and body clear of the worktable when operating the machine.
Wear approved safety eye or face protection when operating the machine. If dust is generated respiratory protection must be worn.
DO NOT
operate the machine when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
leave the machine running unattended.
DO NOT
touch the abrasive whilst operating, or whilst sander is plugged into the mains power.
DO NOT
switch the machine on while the workpiece is in contact with the abrasive.
DO NOT
operate the machine if any parts are damaged or missing as this may cause failure or possible personal injury.
DO NOT
allow children or untrained persons to operate the machine. Keep them away from the work area.
DO NOT
use the machine for any purpose other than wood finishing.
When not in use unplug from the mains power supply and make every effort to ensure the machine is childproof.
INSTRUCTIONS FOR:
BOBBIN SANDER
MODEL No:
SM1301
1.1.
ELECTRICAL SAFETY.
WARNING! It is the user’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and
all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products that are plugged
into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current Device by
contacting your Sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1. The
Electricity At Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power
supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads and plugs for wear and damage and all electrical connections
to ensure that none is loose.
1.1.6.
Important:
Ensure the voltage marked on the product is the same as the electrical power supply
to be used and check that plugs are fitted with the correct capacity fuse. A 13 amp plug may
require a fuse smaller than 13 amps for certain products see fuse rating at right.
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damaged leads, plugs or connections. Immediately replace or have
repaired by a qualified electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage,
cut off and fit a new plug according to the following instructions (discard old plug safely).
(UK only - see diagram at right).
Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the gREEN/YEllOW earth wire to the earth terminal ‘E’.
b) Connect the bROWN live wire to live terminal ‘l’.
c) Connect the bluE neutral wire to the neutral terminal ‘N’.
After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and that the restraint is tight.
Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always
marked with this symbol .
To re-wire, connect the brown and blue wires as indicated above.
DO NOT
connect the brown or
blue to the earth terminal.
1.1.10. Some products require more than a 13 amp electrical supply. In such a case,
NO
plug will be fitted.
You must
contact a qualified
electrician to ensure a 30 amp fused supply is available. We recommend you discuss the installation of a industrial round pin plug and
socket with your electrician.
1.1.11.
Cable extension reels
. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD
fitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cores in the cable
reel is important. Use 1.5mm² section cable as a minimum but to be absolutely sure that the capacity of the cable reel is
suitable for this product and for others that may be used in the other output sockets, we recommend the use of 2.5mm² section cable.
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
FuSE RATINg
THIS PRODUCT MUST BE
FITTED WITH A
13
AMP FUSE
Brown
Live
Wire
Original Language Version
SM1301 Issue: 2 - 23/03/10
