1.2.GENERAL SAFETY INSTRUCTIONS
p
p
WARNING! Compressor must only be serviced by an authorised agent.
3
Familiarise yourself with the application and limitations of the compressor.
3
Ensure the compressor is in good order and condition before use. If in any doubt do not use the unit and contact an electrician/service agent.
3
Before moving, or maintaining the compressor ensure it is unplugged from the mains supply and that the air brush is disconnected.
3
Do not attach anything other than an air brush to the compressor.
3
Only use recommended air brush attachments and parts. To use non-recommended items may be dangerous and will invalidate your warranty.
3
Ensure the safe working pressure of any air brush used, exceeds the units output pressure.
3
Ensure the area selected for spraying is provided with suitable ventilation.
3
Ensure the compressor is turned off before disconnecting the air brush.
3
To move the compressor use the handle only.
3
Use the compressor in a well ventilated area and ensure it is placed on a firm surface.
3
Keep tools and other items away from the compressor when it is in use, and keep area clean and clear of unnecessary items.
3
Ensure the air brush supply hose is not tangled or twisted, or pinched.
3
Keep children and unauthorised persons away from the working area.
7
DO NOT dis-assemble compressor for any reason. The unit must be checked and serviced by an approved service agent.
7
DO NOT use the compressor outdoors, or in damp, or wet locations.
7
DO NOT operate within the vicinity of flammable liquids, gases or solids.
7
DO NOT touch compressor cylinder head as it may be hot and will remain so for some time after shutdown.
7
DO NOT attempt to move the compressor by pulling the air brush supply hose. Only move the compressor by its handle.
7
DO NOT use this product to perform a task for which it has not been designed.
INSTRUCTIONS FOR:
MINI AIR BRUSH
COMPRESSOR
MODEL:
AB900
The use of symbols in this document is to attract your attention to possible danger. The symbols and warnings themselves do not eliminate any danger, nor are they substitutes for correct
accident prevention measures.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
AB900 - 1 - 010203
1. SAFETY INSTRUCTIONS
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.1.
ELECTRICAL SAFETY
p
WARNING!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.
A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1. The
Electricity at Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6.
Important:
Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7.
DO NOT
pull or carry the appliance by the power cable.
1.1.8.
DO NOT
pull the plug from the socket by the cable.
1.1.9.
DO NOT
use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK
3 pin plug is damaged, cut the cable just above the plug and
dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal E.
b) Connect the BROWN live wire to the live terminal L.
c) Connect the BLUE neutral wire to the neutral terminal N.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation
extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.
To rewire, connect the wires as indicated above -
DO NOT
connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that a
suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm
2
, but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of
2.5mm
2
section cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use.
FUSE RATING 3 AMP
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
