SAFETY GUARD FOR PPF20S, PPF30S &
PPFS301S PRESSES
MODEL NO:
PPFSG1, PPFSG2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
I
MP
PO
R
RTA
TANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH
HE
P
PR
O
ODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE
ER
S
SON
NAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
Familiarise yourself with the applications, limitations and hazards peculiar to the safety guard.
Maintain the safety guard in good condition.
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
warranty.
Keep the safety guard clean for best and safest performance.
Ensure the safety guard is correctly attached before operating the press.
Ensure that all fittings are tight before each use.
Remove ill fitting clothing. Remove ties, watches, rings, loose jewellery and contain long hair.
Keep hands and body clear of the safety guard when operating the press.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip footware.
Keep children and unauthorised persons away from the working area.
DO NOT
use the guard for purposes other than those it was designed for.
WARNING!
Always, refer to the safety instructions provided in your press’ instruction manual.
WARNING!
The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product,
but must be applied by the operator.
2. INTRODUCTION
Lightweight steel frame with tough 4.8mm Polycarbonate screen. Adjustable guard protects the user and/or passer by from being injured if
workpiece is accidentally dislodged under load. Bolts onto either side of the table and features six height increments, allowing the workpiece
to be placed onto table with no obstruction. One-way spring loaded locking clips then allow the guard to be pulled up quickly and snap
straight into position for full protection.
3. SPECIFICATION
Model No: .....................................................................................PPFSG1 ................................................................ PPFSG2
Application(s): ................................................................ PPF20S, PPF30S ............................................................... PPF301S
4. ASSEMBLY
Unpack the product and check contents. Should there be any damaged or missing parts contact your supplier immediately.
Refer to attached parts list.
4.1.
ATTACH HANDLE GRIP
4.1.1.
Remove protective
fi
lm from PC board (#1).
4.1.2.
Position handle grip (#5) onto PC board (#1) and secure with
fl
at washer M5 (#3) and machine screw pan head M5 x 10 (#2).
4.2.
ATTACH LOCKING KNOB
4.2.1.
Screw locking knob (#18) into threaded insert located at the top, left hand side of the frame (#8).
5. OPERATION
5.1.
ATTACH THE SAFETY GUARD
5.1.1.
Lift up the safety guard by taking hold of the side grips (#10).
NOTE:
Handle grip (#5) to be facing outwards and at it’s lowest position (fig 2).
5.1.2.
Insert the T-shape screws (#9) into the key holes located on the front of the press’ working table (
fi
gs 1 & 3).
WARNING!
Ensure that both the T-shape screws are fully located into the key slots. Failure to do so may result in the safety guard
becoming detached from the press causing possible personal injury and damage to the safety guard.
5.2.
INSERTING THE WORKPIECE
5.2.1.
Holding the handle grip (#5) turn the locking knob (#18) counter clockwise (
fi
g 2) and raise the safety guard PC board (#1) fully to
the top (
fi
g 2).
5.2.2.
Lock the PC board (#1) into place by turning the locking knob (#18) clockwise (
fi
g 2).
DO NOT
over tighten.
5.2.3.
Insert the workpiece onto the presses working table.
PPFSG1, PPFSG2 Issue 1 23/03/22
Original Language Version
© Jack Sealey Limited
Refer to
instructions
