INSTRUCTIONS FOR:
AIR REGULATOR, FILTER, LUBRICATOR RANGE
Models:
SA106, SA106FR, SA106F, SA106L, SA106R
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1.
SAFETY INSTRUCTIONS
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
!
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
!
WARNING!
Disconnect the equipment from the air supply before changing accessories, servicing or performing any maintenance.
"
Keep the equipment clean and maintain it in good condition (use an authorised service agent).
"
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
!
WARNING!
Ensure that the correct air pressure is maintained and not exceeded.
"
Keep air hoses away from heat, oil and sharp edges. Check hoses for wear before each use and ensure that all connections are secure.
#
DO NOT
direct air from the air hose at yourself, others or animals.
"
Drain the compressor air tank daily. Water in the air line will damage your equipment.
"
When work is complete ensure that the air supply is turned off.
Suitable for workshop air supply set-ups. Regulator features locking control knob for pre-setting air pressure and pressure gauge. Filter has
manual drain facility with female 1/8”BSP outlet. Lubricator includes oil/air mix control and sight glass. Filter and lubricator are fitted with
metal bowl cages for protection. SA106, SA106FR and SA106R supplied with mounting bracket.
2.
INTRODUCTION & SPECIFICATIONS
Filter/Lubricator/Regulator - SA106
Max. inlet pressure . . . . . . . . . . . . . . . . . . .150psi (10.3 bar)
Max. outlet pressure . . . . . . . . . . . . . . . . . . .125psi (8.6 bar)
Max. flow rate @ 100psi (6.9 bar) . . . . . . . . . . . . . . . .60cfm
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 micron
Lubricant . . . . . . .Sealey Air Tool Oil - ATO/500 or ATO/1000
Ports-Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/8”BSP
Filter/Regulator - SA106FR
Max. inlet pressure . . . . . . . . . . . . . . . . . . .150psi (10.3 bar)
Max. outlet pressure . . . . . . . . . . . . . . . . . . .125psi (8.6 bar)
Max. flow rate @ 100psi (6.9 bar) . . . . . . . . . . . . . . . .70cfm
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 micron
Ports-Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/8”BSP
Regulator - SA106R
Max. inlet pressure . . . . . . . . . . . . . . . . . . .150psi (10.3 bar)
Max. outlet pressure . . . . . . . . . . . . . . . . . . .125psi (8.6 bar)
Max. flow rate @ 100psi (6.9 bar) . . . . . . . . . . . . . . . .88cfm
Ports-Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/8”BSP
Filter - SA106F
Max. inlet pressure . . . . . . . . . . . . . . . . . . .150psi (10.3 bar)
Max. outlet pressure . . . . . . . . . . . . . . . . . . .125psi (8.6 bar)
Max. flow rate @ 100psi (6.9 bar) . . . . . . . . . . . . . . . .53cfm
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 micron
Ports-Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Lubricator - SA106L
Max. inlet pressure . . . . . . . . . . . . . . . . . . .150psi (10.3 bar)
Max. outlet pressure . . . . . . . . . . . . . . . . . . .125psi (8.6 bar)
Max. flow rate @ 100psi (6.9 bar) . . . . . . . . . . . . . . . .60cfm
Lubricant . . . . . . .Sealey Air Tool Oil - ATO/500 or ATO/1000
Ports-Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
WARNING! Filter and lubricator bowls are manufactured
from polycarbonate and must not be used at temperatures
over 125
O
F (52
O
C) or for pressures over 218psi (15 bar).
Polycarbonate can be damaged and may fail if exposed to
certain solvents either internally or externally - strong
alkalies, compressor oils containing aromatic hydrocarbons
or fire retardant oils, or the fumes of any of these.
Clean with warm water only.
SA106/106FR/106F/106L/106R - 1 - 120406
SA106
SA106FR
SA106F
SA106L
SA106R
