background image

0.5tonne Low ProfiLe engine Crane

Model no:

 PH5

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  Safety

 

9

   Keep crane, lifting slings, support and beams in good working order and condition. Follow the inspection requirements as described   

  in Section 6 Maintenance. Take immediate action to repair or replace damaged parts by contacting your supplier. ensure that all  

 

  accessory lifting devices are suitably certified. If crane is damaged, remove from service immediately.

 

9

   ensure the surface on which the crane is used is level, firm and capable of supporting the weight of the crane with maximum load - we  

  recommend concrete. never use the crane on tarmacadam or other soft surfaces.

 

9

   Keep children and unauthorised persons away from the working area.

 

9

   Keep working area clean and tidy, free from unrelated materials and ensure that there is adequate lighting.

 

9

   ensure that load does not exceed the maximum lifting capacity of the crane. overloading the crane is dangerous. Where appropriate,  

  use only the lifting points recommended by the manufacturer of the item to be lifted, e.g. vehicle engine.

 

9

   Before lifting the load ensure that the crane jib is in the lowest practical position, that there are no obstacles which may snag the load  

  whilst it is being lifted and that the area above the jib is clear.

 

9

   To avoid injury, be fully aware of your own and other persons locations in relation to the lifting, and lowering, of the load.

 

9

   Keep a sound footing and balance, and ensure the floor is not slippery.

 

9

   ensure jib extension locking bolt and nut are in position before lifting.

 

9

   ensure the centre of gravity always remains inside the crane base and is as close as possible to the vertical portion of the lifting  

 

  member as possible.

 

8

  

Do not

 harness the load at an angle or use any attachments not verified as fit for purpose.

 

8

  

Do not

 allow the load to swing during lifting. 

 

8

  

Do not

 allow the load to drop suddenly. lower load with care, ensuring that you are fully aware of the condition of the surface onto  

  which the load is to be placed. 

 

8

  

Do not

 load crane beyond its rated capacity for each specified jib extension position as indicated in Section 3. The capacity of the   

  crane reduces as the jib is extended.

 

8

  

Do not

 position any part of your body beneath the load.

 

8

  

Do not

 use the crane to move or transport a load other than for repositioning. The crane is a lifting device only.

 

8

  

Do not

 apply any sideways pressure to any part of the crane during lifting or when a load is suspended.

 

8

  

Do not

 attempt to adjust the safety valve, which has been set and sealed by the manufacturer.

 

8

  

Do not

 use this product to perform a task for which it is not designed.

 

8

  

Do not

 use whilst under the influence of drugs, alcohol or intoxicating medication.

 

8

  

Do not

 attempt to modify or alter this unit. 

 

8

  

Do not

 climb on the crane.

 

9

   When not in use fold the crane down and store in a safe, dry, childproof area.

 

9

   This crane is designed for lifting within a garage or workshop environment.

 

‰

  

warning!

 Failure to heed safety and warning instructions may result in damage and/or personal injury and will invalidate the  

 

 warranty.

2.  introDuCtion

 

low entry engine crane with a height of only 100mm at the wheels. Weighs only 37kg so is extremely lightweight and manoeuvrable.  

 

Heavy-duty castors and pump access from side, for safe handling of loads. delivered in knock-down form to reduce freight costs,   

 

some self-assembly required.

2.1.    

iDentifiCation: 

Supplier:  Sealey Power Products, 

Kempson Way, 

Suffolk Business Park, 

Bury St edmunds, 

Suffolk, 

IP32 7AR.

Model no: PH5

PH5           Issue 1       04/12/19

Original Language Version

© Jack Sealey limited

Refer to 

instructions

 Wear protective 

gloves

 Wear safety 

footwear

Reviews: