Motorcycle centre Stand Moving dolly
model no:
MS0651
thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. Safety
9
maintain the
dolly in good condition (use an authorised service agent).
9
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
locate the dolly in a suitable work area. Keep area clean and tidy and free from unrelated materials, and ensure that there is adequate
lighting.
9
ensure that the floor is level and strong enough (preferably concrete) to take the weight of the dolly and the motorcycle.
8
do not
use the dolly on tarmacadam, as the surface may be unstable.
9
Keep the dolly clean for best and safest performance.
8
do not
exceed the rated capacity, the maximum motorcycle weight is 220kg.
9
maintain correct balance and footing,
do not
over reach. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
8
do not
use the dolly for a task it is not designed to perform.
8
do not
use the dolly if it is damaged.
8
do not
use the dolly when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do not
allow untrained persons to use the dolly.
8
do not
make any modifications to the dolly.
9
Before storing in safe area, ensure that all parts are clean and free of grease and oil.
Warning!
The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur.
It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the
operator.
2. introduction
This motorcycle moving dolly can be used to manoeuvre motorcycles (up to 220kg vehicle weight) with centre-stands and is perfect for places
where space is restrictive. The centre stand locates on the 4mm thick hardened steel plate and the 360 degree castors allow the bike to be
moved in any direction. Complete with a hand operated built-in-brake mechanism which is ideal for workshop, showroom and home garage use.
3. Specification
Model no: . . . . . . . . . . . . . . . . . . . . . . . . . . . MS0651
Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220kg
4. aSSeMbly
5.1.
Attach the castors securely using nylock nuts.
note:
The castors do not have brakes attached.
5. operation
5.1.
Apply the brake on the dolly by rotating the handle as shown in (fig.1)
to position shown in (fig.2).
5.2.
Position the dolly under the motorcycle.
5.3.
line up the motorcycle centre stand with the dolly.
5.4.
Kick the stand down so it is positioned in the centre of the dolly
and raise the bike onto the centre stand.
5.5.
Release the brake by moving the brake handle as shown in (fig.2).
5.6.
Holding the handle bars, move the bike in any direction.
5.7.
Apply the brake to prevent dolly moving.
6. Maintenance
6.1.
Wipe with a damp cloth to remove dirt.
6.2.
Blow with compressed air to remove dust and keep the castors clean.
mS0651 | Issue 2 06/09/2019
Original Language Version
© Jack Sealey limited
Refer to
instructions
fig.1
fig.2
