Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
2.1.
Ideal for use with off-road/trials bikes. Easily lifts the bike when performing maintenance/services or cleaning. Simple, one foot, step
and lift mechanism means the bike can be instantly raised in one motion.
2. INTRODUCTION & SpECIFICATION
DO NOT
sit on the motorcycle on the stand.
DO NOT
start the motorcycle on the stand.
DO NOT
mount the stand on tarmacadam, as the surface may be unstable.
DO NOT
use the stand for a purpose it is not designed to perform.
DO NOT
operate the stand if it is damaged.
DO NOT
use the stand when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
allow untrained persons to operate the stand.
DO NOT
make any modifications to the stand.
DO NOT
operate the stand if parts are missing or damaged.
DO NOT
exceed the maximum capacity.
Maintain the
stand in a good clean condition for the best and safest performance.
Locate the stand and motorcycle in a suitable area. Keep area clean, tidy and free from unrelated materials and ensure that there is
adequate lighting. Also ensure that the floor/ground is level and strong enough (preferably concrete) to take the weight of the stand
and the motorcycle.
Maintain correct balance and footing whilst positioning the motorcycle on the stand,
DO NOT
over reach.
Ensure that the floor is not slippery, wear non-slip footwear. Also essential for safe operation of the foot pedal.
Keep children and unauthorised persons away from the work area.
Before removing a motorcycle from the stand, ensure that there are no obstructions or persons around the motorcycle.
Always support motorcycle to prevent falling.
If using as a front stand, always use in conjunction with another suitable rear stand to ensure full stability.
When not in use, store in a safe, dry, childproof location.
IMPORTANT:
pLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OpERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE pRODUCT CORRECTLY AND WITH CARE FOR THE pURpOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR pERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. pLEASE KEEp INSTRUCTIONS SAFE FOR FUTURE USE.
2.2. Specification.
Model No: ................................................................. MpS1.V2
Minimum Height: ............................................................300mm
Maximum Height: ...........................................................400mm
Maximum Capacity: .........................................................150kg
3. ASSEMbLY INSTRUCTIONS
INSTRUCTIONS FOR:
QUICK LIFT STAND FOR OFF-ROAD/TRIALS
bIKES 150kg
MODEL No:
MpS1.V2
The stand consists of three main items. Item [
A
] base frame, [
b
] platform frame and [
C
] foot pedal assembly. Ancilliary items
include a plastic roller, two circlips, an 18mm washer, split pin and a set of M6 fixings. Some items in
3.1.-3.3.
may already be fitted.
3.1.
With the roller and two circlips fitted, slide the foot pedal [
C
] spindle (fig.1) through the vertical pillar boss of the base frame [
A
],
retain with washer and split pin.
3.2.
Offer the platform tubular pillars over the base tubular pillars; the foot pedal roller aligned with platform roller guides.
3.3.
Fit the foot pedal extension with the M6 screw, washer and stiff nut.
Original Language Version
MPS1.V2 Issue: 1 - 27/12/13
© Jack Sealey Limited 2013
330
Over centre
locked position
Extension removed and retained.
2.5:1 (approx.) initial mechanical advantage
(effort diminishes to zero as platform raises)
Stand fully elevated and locked.
Retained
fixings
fig.1
fig.2
300 min
400 max
Circlip (inner)
Washer and split pin
Roller and
circlip
[
A
]
[
b
]
[
C
]
150kg max
Rubber
tread
Rubber pad
Roller guides
