12/24V 120W SMD LED MINI LIGHT BAR -
MAGNETIC BASE, SINGLE POINT FIXING
MODEL NO:
MLB80MB, MLB80SB
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
Familiarise yourself with this product’s application and limitations, as well as any specific potential hazards peculiar to the beacon.
9
Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the
warranty.
8
DO NOT
use the beacon for any purpose other than for which it is designed.
8
DO NOT
allow children to operate the beacon.
8
DO NOT
operate the beacon if any parts are missing or damaged as this may cause failure or possible personal injury.
9
When not in use switch the beacon off and where appropriate remove plug from power supply.
2. INTRODUCTION
MLB80MB
E
xtremely bright 120W amber LED high intensity mini light bar fitted with a high strength magnet strong enough to cope with normal
road speeds and ease of installation. 10 Modules fitted with 8 LEDs allowing a 360° light. Fitted with a 3mtr cable and cigarette
lighter power plug. Plug includes 2 switches, on/off and a momentary switch, giving you the option of 9 different flash patterns.
Built-in memory recalls last pattern selected. ECE R65 & R10 Approved for highway use. CE Approved and E-Marked. IP56 rated.
MLB80SB
E
xtremely bright 120W amber SMD LED high intensity mini light bar fitted with a 10mm single bolt fixing. 10 Modules fitted with 8 LEDs,
creating a 360° light. Built-in 10 option flash pattern that has a built-in memory which recalls the last pattern selected. ECE R65 & R10
Approved for highway use. CE Approved and E-Marked. IP56 rated.
3. SPECIFICATION
Model No:
............................................MLB80MB, MLB80SB
Dimensions:
................. 279mm (w) x 61mm (h) x 165mm (d)
S
upply:
................................................................. 12-24V DC
Temperature Range:
......................................-30°C to +50°C
4. OPERATION
4.1.
WIRING
4.1.1.
Black wire should be wired to a suitable earth.
4.1.2.
Red wire should be wired via a switch to a suitable fused 12V
live supply fitted with a 5 amp fuse.
4.1.3.
Yellow wire should be wired to earth via a momentary
switch (negative earth).
4.2.
ATTACHING THE LIGHT TO YOUR VEHICLE
4.2.1.
There are two strong magnets on the reverse of the unit.
(fig.1)
4.3.
ATTACHING THE LIGHT BAR VIA THE SCREW FITTING
4.3.1.
The screw can be removed from the underside of the light
bar by removing the fixing plate. (fig.1)
4.3.2.
Under the fixing plate there is a recess for the head of
the setscrew to sit in. This will stop the setscrew from
turning when tightening the nut. (fig.2)
4.4.
SWITCHING ON AND CHANGING THE LIGHT
PATTERN
4.4.1.
There are two buttons on the in car adaptor. One switch
(with LED indicator light) switches the light on and off.
The
other switch switches light patterns. (fig.3)
M
LB80MB, MLB80SB Issue 2 (4) 28/07/22
Original Language Version
© Jack Sealey Limited
Refer To
Instructions
fig.1
fig.2
Warning! Do Not
Look Directly Into
Light.
Warning! Hot
Surfaces
