Original Language Version
Numbers in BOLD refer to the diagram in Fig.1
2.1
To assemble the side frames compress the silver latch
button at the top of the front frame
1
and insert the tube
into the back frame tube
1A
until they snap together.
2.2
Onto each end of the two paper bars
20
slide a paper
holding ring
5
followed by a washer
16,
holding spring
17
and another washer
16,
followed by a paper holding
ring
5
. Insert a screw
12
into the threaded block on each
holding ring.
2.3
Attach the side frames to each end of the paper bars as
shown in the main drawing using the four wing bolts
13
.
2.4
Fit the bottom tool tray between the side frames and bolt
it to each leg using bolt
10
, nut
22
and washer
23
.
2.5
Attach the upper paper blade
7
to the front of the frame
using two screws
10
, two nuts
22
and two washers
23
.
2.6
Attach the lower cutting blade
7
to the front of the frame
using two screws
10
, two nuts
22
and two washers
23
.
2.7
Attach a paper spring
7A
to the back edge of each
cutting blade. Hook one end of the spring to the notched
back corner of the metalwork and stretch it across and
hook it to the other back corner. Take care to avoid the
cutting blade teeth when doing this.
2.8
To assemble the four tape reels as shown in Fig.2 take a
long bolt
14
and screw on to it a wing nut
6
then drop a
washer
23
onto it followed by a metal bush
21
. Slide a
reel
8
over the bolt and onto the bush ensuring that it is
the right way round. Retain the assembly using another
washer followed by a wing nut
6
. After the nut has been
tightened the reel should still run freely on the bush.
Attach another nut to the bolt and insert the bolt through
the frame in one of the four places indicated on the main
drawing. Retain the assembly in place using a nut
22
and a washer
23
.
2.9
Attach the small tool tray
15
to the side of one of the
frames using two screws
10
, two nuts
22
and two
washers
23.
The nuts and washers should be on the
inside of the tray.
2.10
Attach the hanger
9
to the side of the opposite frame
at the same level as the top tray. Insert the ends of the
hanger into the holes in the side of the frame, tip the
hanger forwards so that the first bend in either end of
the hanger is inside each frame tube.
2.11
The MK66.V4 has a solid rod axle
4
with holes at either
end to accept cotter pins
11.
Slide the axle through the
holes near the bottom of each rear leg.
2.12
Slide a wheel
3
onto each end of the axle and retain it
with a cotter pin
11
through the axle. Secure by bending
the pin back onto itself.
2.13
. Push a plastic tube cover
19
over each front leg.
INSTRUCTIONS FOR:
MASKING PAPER DISPENSER
MODEL No:
MK66.V4
1
FRONT FRAME
1A
REAR FRAME
2
TOOL TRAY (LARGE)
3 WHEEL
4 AXLE
5
PAPER HOLDING RING
6
WING NUT
7
CUTTING BLADE
7A
CUTTING BLADE SPRING
8
TAPE REEL
9
HANGER BAR
10 BOLT
11
COTTER PIN
Ensure the dispenser is on a reasonably flat, level floor before loading.
Ensure that all fittings are tight and secure.
Be aware that the paper cutting blades are sharp, handle with care.
DO NOT
use the dispenser for any purpose other than that for which it is designed.
12
WING BOLT M5 x 15
13
WING BOLT
14
LONG BOLT
15
SMALL TOOL TRAY
16
PAPER HOLDING WASHER
17
PAPER HOLDING SPRING
18
HANDLE GRIP
19
PLASTIC TUBE COVER
20
PAPER BAR
21
BUSHING FOR TAPE REEL
22
NUT M6
23
WASHER M6
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions and maintained properly, give you years of trouble free performance.
Refer to Instruction
Manual
1. SAFETY
2. ASSEMBLY
© Jack Sealey Limited
MK66.V4 Issue: 1 - 24/06/16
Fig.1
