INSTRUCTIONS FOR:
ABRASIVE DISC CUT-OFF SAW
Models:
MG214/230V
MG214/110V
Thank you for purchasing a Sealey product. Manufactured to a high
standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
The use of symbols in this document is to attract your attention to possible danger. The symbols and warnings themselves do not eliminate any danger, nor are they substitutes for proper
accident prevention measures.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.2
GENERAL SAFETY
p
WARNING!
Disconnect the saw from the mains power, and ensure the cutting disc is at a complete standstill before attempting
to changing accessories, servicing or performing any maintenance.
3
Maintain the saw in good condition (use an authorised service agent).
3
Replace or repair damaged parts.
Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.
3
Locate the saw in an adequate working area for its function. Ensure the surface is flat and firm. Keep area clean and tidy and free from
unrelated materials, and ensure there is adequate lighting.
3
Keep the saw clean for best and safest performance and check moving parts alignment regularly.
p
WARNING!
Before each use check cutting disc is secure, and the disc is not worn or damaged, if so replace immediately.
NOTE:
Only persons qualified under the Abrasive Wheels Regulations holding a current grinding wheel certificate may change discs (wheels).
3
Ensure replacement discs are not damaged in any way such as cracks, deformations or splinters etc. Also check the mounting flanges
to ensure they are not deformed, burred or chipped. Damaged items must not be used as they may cause irregular pressure on the disc
which may cause the disc to break. DO NOT over tighten a disc and never tamper with a disc in order to adapt it to a different size holder.
3
Always use the correct disc suitable for the material being cut. Ensure the cutting discs maximum speed specification is higher than that
indicated on the machine data plate. Once mounted on the grinder test the disc before use by facing the grinder in a safe direction
(point away from yourself, others and vulnerable items) and run for a short time.
p
WARNING!
Keep guard and holding screws in place, tight and in good working order. Check regularly for damaged parts.
A guard or any other part that is damaged should be replaced with a new one to ensure that it operates properly and perform its intended function
before the tool is used. The safety guard is a mandatory fitting where saw is used in premises covered by the Health & Safety at Work Act.
3
Remove adjusting keys and wrenches from the machine and its vicinity before turning it on.
p
WARNING!
Wear approved safety eye protection, ear defenders, and gauntlets, and if dust is generated respiratory protection.
3
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.
3
Keep hands and body clear of the work table when operating the saw, and position your body in line with the abrasive wheel whilst cutting.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
MG214/230V & MG214/110V - 0016 - 130798
1.1.
ELECTRICAL SAFETY.
p
WARNING!
It is the users responsibility to read, understand and comply with the following:
You must
check all electrical equipment and appliances to ensure they are safe before using.
You must
inspect power supply leads, plugs
and all electrical connections for wear and damage.
You must
ensure the risk of electric shock is minimised by the installation of appropriate
safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that
an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use an RCD together with portable products
that are plugged into an electrical supply not protected by an RCCB. If in doubt consult a professional electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1. The
Electricity At Work Act 1989
requires all portable electrical appliances, if used on a business premises, to be tested by a qualified
Electrician at least once a year by using a Portable Appliance Tester (PAT).
1.1.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of the appliance,
and the safety of the appliance operator.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply.
See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage,
especially power connections, to ensure that none are loose.
1.1.6.
Important:
Ensure the voltage marked on the product is the same as the electrical power supply
to be used, and check that plugs are fitted with the correct capacity fuse. A 13Amp plug may require
a fuse smaller than 13Amps for certain products (
subject to 1.1.10. below)
see fuse rating at right.
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead. Products such as welders
must not be pulled or carried by their output cables.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired
by a qualified Electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage,
cut off and fit a new plug according to the following instructions (discard old plug safely).
(UK only - see diagram at right).
Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the GREEN/YELLOW earth wire to the earth terminal E.
b) Connect the BROWN live wire to live terminal L.
c) Connect the BLUE neutral wire to the neutral terminal N.
After wiring, check there are no bare wires, that all wires have been correctly connected and that the wire restraint is tight.
Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always marked
with this symbol .
To re-wire, connect the brown and blue wires as indicated above. DO NOT
connect the brown or blue to the earth terminal.
1.1.10. Some products require more than a 13Amp electrical supply. In such a case,
NO
plug will be fitted.
You must
contact a qualified Electrician
to ensure a 30 amp fused supply is available. We recommend that you discuss the installation of a industrial round pin plug & socket with your Electrician.
Blue
Neutra
l
Yellow & Green
Earth wire
wire
restrai
FUSE RATING
THIS PRODUCT MUST BE FITTED WITH A:
13
Amp FUSE
Brown
Live
wire
