![background image](http://html1.mh-extra.com/html/sealey/led24110/led24110_instructions_1224818001.webp)
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
LED24110, LED48110 Issue:1 05/06/18
Original Language Version
© Jack Sealey Limited
SITELIGHT 24/48W SMD LED 110V
MODEL NO’S:
LED24110, LED48110
Refer to
instruction
manual
1. SAFETY
1.1.
ELECTRICAL SAFETY
PLUG & MAINS POWER SUPPLY
WARNING!
It is the owner’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure that they are safe before using. You must inspect power supply leads,
plugs and all electrical connections for wear and damage.
You must
also read and understand the following instructions concerning
electrical safety.
NOTE:
110 volt lights are usually operated by connecting to a transformer or a generator. Check to ensure all supply equipment is
compatible with the rating of the light.
1.1.1.
The
Electricity At Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2.
The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of the appliance and the
safety of the appliance operator.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3.
Ensure the insulation on all cables and the product itself is safe before connecting to the power supply. See 1.1.1. & 1.1.2. above and
use a Portable Appliance Tester (PAT).
1.1.4.
Ensure that cables are always protected against short circuit and overload.
1.1.5.
Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage and especially power connections to
ensure that none are loose.
1.1.6.
Important:
Ensure the voltage marked on the product is the same as the electrical power supply to be used and check that plugs are
fitted with the correct capacity fuse.
1.1.7.
Important:
For use of a 110 volt light - ensure that the 110 volt transformer or generator is adequately rated.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull plugs from sockets by the power cable.
8
DO NOT
use worn or damaged leads, plugs or connections. Immediately replace or have
repaired by a qualified electrician. A U.K. 3 pin 110 volt plug with ASTA/BS approval is fitted.
In case of damage, cut off and fit a new plug according to the following instructions
(discard old plug safely).
Ensure the unit is correctly earthed via a three-pin plug. FOR 110 VOLT PLUG SEE fig.1.
a)
Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b)
Connect the BROWN live wire to live terminal ‘L’.
c)
Connect the BLUE neutral wire to the neutral terminal ‘N’.
d)
After wiring, check that there are no bare wires, that all wires have
been correctly connected, that the cable external insulation extends beyond the cable
restraint and that the restraint is tight.
1.1.8.
Cable extension reels
. When a cable extension reel is used it should be fully unwound before
connection. The section of the cores of the cable is important and should be at least 1.5mm², but
to be absolutely sure that the capacity of the cable reel is suitable for this product and for others
that may be used in the other output sockets, we recommend the use of 2.5mm² section cable.
1.2.
GENERAL SAFETY
WARNING! Disconnect light from the power supply before servicing or performing any
maintenance.
9
Maintain the light in good condition. Repairs must only be undertaken by a qualified electrician (use an authorised service agent).
9
Replace or repair damaged parts. Use recommended parts only, unauthorised parts may be dangerous and will invalidate the
warranty.
9
Locate the light in an adequate area for its function, keep area clean and tidy and free from unrelated materials.
9
If you use an extension lead
the cable must be fully unwound from the drum
.
9
The light is weatherproof and may be used outdoors. Ensure any extensions and plugs are weatherproof.
▲
DANGER! DO NOT direct the light into a person’s eyes.
8
DO NOT
use the light without the weather seals intact.
8
DO NOT
use the light near flammable, combustible or explosive liquids, solids, gases or equipment.
9
When not in use, switch off the light and disconnect from the power supply. Ensure that the unit is cool and dry and then store in a
safe, dry, childproo
f location.
9
9
9
fig.1