instructions for:
HVLP Pressure Pot system
model no:
HVLP-79/P.V2
thank you for purchasing a sealey product. manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT
:
PLeAse reAD tHese INstruCtIoNs CAreFuLLy. Note tHe sAFe oPerAtIoNAL reQuIremeNts, WArNINGs, AND
CAutIoNs. use tHIs ProDuCt CorreCtLy, AND WItH CAre For tHe PurPose For WHICH It Is INteNDeD. FAILure to Do so mAy
CAuse DAmAGe AND/or PersoNAL INJury AND WILL INVALIDAte tHe WArrANty.
familiarise yourself with the application, limitations and potential hazards peculiar to the spray gun.
WARNING!
disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.
maintain the
spray gun in good condition (use an authorised service agent).
replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Keep the spray gun clean for best and safest performance.
ensure that the compressed air system can supply the spray gun air consumption (10cfm).
Wear approved safety respiratory protection and safety eye goggles.
if spraying isocyanate based finisher, wear approved respirator/clean air breathing apparatus and protect skin with latex gloves and an
impervious hooded coverall.
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and tie back long hair.
locate the spray gun in a suitable work area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate
ventilation and lighting.
Keep children and unauthorised persons away from the work area.
When not in use, ensure that the air supply is turned off.
Avoid unintentional operation of spray gun.
Do Not
point spray gun at yourself, other persons or animals.
Do Not
direct air from the air hose at yourself, other persons or animals.
Do Not
carry the spray gun by the hose, or yank the hose from the air supply.
Do Not
exceed the maximum air pressure of 50psi.
Do Not
use the spray gun for any purpose other than that for which it is designed.
Do Not
allow untrained persons to operate the spray gun.
Do Not
get the spray gun wet or use in damp or wet locations or in areas where there is condensation.
Do Not
operate the spray gun if any parts are missing or damaged as this may cause failure and/or personal injury.
When not in use, disconnect the spray gun from the air supply, clean thoroughly and store safely.
1. sAFety INstruCtIoNs
2. DesCrIPtIoN & sPeCIFICAtIoN
fully polished metal gun body resists corrosion and has low affinity for paint, making this unit ideal for water based paints and easy to clean.
Adjustable paint, fan width and air regulator controls. High capacity pressure pot holds up to two litres of paint per fill. this unit is perfectly suited
to the commercial refinishing shop. components from the HVlP-79/P are also available separately. supplied with 1.7mm set-up with optional
set-ups available separately.
set up: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7mm
Available set ups: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3, 1.4, 1.5, 2.0mm
Air Pressure:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-50psi
Air consumption: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10cfm
Pot capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0ltr
3. AIr suPPLy
recommended supply system is shown below.
3.1
ensure that the spray gun trigger is in the "off" position before connecting to the air supply.
3.2
You will require an air pressure between 15 - 50psi, and an air flow according to the specification.
WArNING!
ensure that the air supply is clean and does not exceed 50psi while operating the spray gun. too high an air pressure and/or
unclean air will shorten the product life, due to excessive wear, and may cause damage and/or personal injury.
3.3
drain the air tank daily. Water in the air line will damage the spray gun
and
invalidate your warranty.
3.4
clean compressor air inlet filter weekly.
3.5
line pressure should be increased to compensate for unusually long air hoses (over 8 metres). the minimum hose diameter should be
1/4” i.d. and fittings must have the same inside dimensions.
3.6
Keep hose away from heat, oil and sharp edges.
check hoses for wear, and make certain that all connections are secure.
Original Language Version
HVlP-79/P.V2 issue: 2 - 2/11/09
