BENCH DRILLS
MODEL NO’S:
GDM50B.V2, GDM92B,
GDM120B.V2, GDM150B.V2, GDM180B.V2,
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.
ELECTRICAL SAFETY
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
Electrical safety information:
it is important that the following information is read and understood.
1.2.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.3.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.4. Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualified electrician.
1.5.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
B) Connect the BROWN live wire to the live terminal ‘L’.
C) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
WARNING! Disconnect drill from mains power before changing accessories, servicing or
performing any maintenance.
WARNING!
Keep all guards and holding screws in place, tight and in good working order. Check
regularly for damaged parts.
9
A guard or any other part that is damaged should be replaced, before the tool is used, to ensure
that it operates properly and perform its intended function. The safety guard is a mandatory fitting where drill is used in premises covered
by the Health & Safety at Work Act.
9
Check alignment of moving parts and check for possible broken parts.
9
Replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Ensure the set screws of the head frame are screwed tight before using the drill.
9
Secure the drill to the workbench or floor.
9
Drill is designed for use with drill bits only.
9
Ensure the chuck is securely fastened to the spindle.
9
Remove adjusting keys, chuck key and wrenches from the machine and working area before switching on.
9
Use clamps or a vice (not included; available from your Sealey stockist) to secure the workpiece.
DO NOT
attempt to hold the
workpiece by hand.
9
Refer to speed chart for recommended drilling speeds.
WARNING! Always wear approved eye or face protection when operating this drill. Use face or dust mask if dust is generated.
9
Keep drill bits clean and sharp for best and safest performance. Follow the instructions for lubrication and changing accessories.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Locate the drill in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
9
Exclude children and non-essential persons from the work area.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Avoid unintentional starting.
GDM Series 50B.V2, 92B, 120B.V2, 150B.V2, 180B.V2 ....Issue1 22/06/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear ear
protection
Wear a mask
Recommended fuse
rating:
13A
Indoor use only
