background image

cOOLING SYSTEM PRESSURE TEST KIT 7Pc - 
cOMMERcIAL

model no: 

cv0011

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, 
and properly maintained, give you years of trouble free performance.

1.  SAFETY

 

‰

  

WARNING!

 ensure all Health & Safety, local authority, and general workshop practice regulations are strictly adhered to when   

 

using product. 

 

‰

  

WARNING!

 ensure the engine and cooling system have cooled down, before opening the radiator cap. 

 

9

  

maintain tools in good and clean condition for best and safest performance. 

DO NOT

 use tester if damaged.

 

9

  

Wear suitable clothing to avoid snagging. 

DO NOT

 wear jewellery and tie back long hair.

 

9

  

Wear approved eye protection. A full range of personal safety equipment is available from your Sealey stockist.

 

9

  

operate in a well ventilated area and avoid breathing in exhaust fumes. 

 

9

  

Always keep a fire extinguisher close by, that is suitable for fuel/electrical/chemical fires. 

 

9

   Keep yourself, tools, and test equipment away from hot engine parts.

 

8

  

DO NOT

 use this tool for any purpose other than that for which it is designed.

 

9

  

never lay tools on the vehicle’s battery. This may short the terminals together, causing harm to yourself, the tools, or the battery.

 

9

  

Account for all tools and parts being used and do not leave any in the engine bay.

 

9

  

Keep children and other unauthorised persons away from the working area.

 

9

  

Keep test kit parts clean, store parts in the carry case, and keep this in a safe, dry, childproof location.

  IMPORTANT: 

Always refer to the vehicle manufacturer’s service instructions, or a proprietary manual to establish the current procedure  

  and data. These instructions are provided as a guide only.

2.  INTRODUcTION

i

C

ooling system pressure testing kit, designed for commercial vehicles. Pressure pump with gauge quickly identifies faulty gaskets, radiators, 

weeping pipes and other causes of coolant loss.

3.  SPEcIFIcATION

model no: .................................................................. CV0011
Applications: dAF, Iveco, man, mercedes, Renault, Scania, Volvo

4.  OPERATION

4.1.    

Setting up.

 

‰

 

WARNING! Ensure the engine and cooling system have cooled down, before opening the radiator cap.

4.1.1. 

  

Remove the radiator cap and clean around the radiator fitting.

4.1.2.   

Select the correct adaptor for the make of vehicle to be tested. Screw the adaptor onto the radiator, checking that the rubber gasket is  

 

correctly seated.

4.1.3.   

Connect the radiator tester to the adaptor by pushing on the quick-release coupling until it clicks.

4.2.    

checking the system.

4.2.1.   

Pump the pump until the gauge indicates approximately 1Bar and leave for one minute.

4.2.2.   

If pressure remains constant for one minute, it will indicate that the system is in good condition.

4.2.3.   

If the pressure falls, it indicates that the system has a leak somewhere, resulting in loss of pressure.

4.2.4.   

Check the system for water leaks, and when located, repair accordingly.

4.2.5.   

If there is pressure loss, but no visible external water leakage, check the condition of the head gasket.

4.2.6.   

Re-test system after repair, to ensure there are no further leaks in the system and that repair is oK.

4.2.7.   

To remove adaptor, release pressure by pressing the valve on the side of the coupling, then remove the quick-release coupling by  

 

pulling back on the sleeve. Remove the adaptor and re-fit the radiator cap. 

CV0011 | Issue:2 (H,F)  13/03/18

Original Language Version

© Jack Sealey limited

Refer to 

instruction

manual

Wear eye

protection

Wear 

protective

gloves

Wear 

protective

clothing

Reviews: