1.1 GENERAL SAFETY.
Disconnect the battery from the grinder unit before changing
accessories, servicing or performing any maintenance.
Maintain the
grinder and battery in good condition. Check
moving parts alignment on a regular basis.
Replace or repair damaged parts.
Use an authorised service
agent and recommended parts only. Unauthorised parts may
be dangerous and will invalidate the warranty.
Ensure the grinder is switched off before installing the battery.
Keep the grinder battery and charger clean for best and safest
performance.
Remove ill fitting clothing. Remove ties, watches, rings and
other loose jewellery and contain long hair.
Evaluate your working area before using the grinder e.g. ceiling,
floors and enclosures may contain electrical items or water piping.
Ensure battery is correctly inserted into the grinder handle
and latched in place before attempting to switch on.
Secure loose workpieces with a clamp, vice or other adequate
holding device.
Avoid unintentional starting.
Wear approved safety eye protection (standard spectacles are
not adequate).
Maintain correct balance and footing. Ensure the floor is not
slippery and wear non-skid shoes.
Be aware that this grinder does not need to be plugged into the
mains power.
Keep children and unauthorised persons away from the
working area.
DO NOT
use the grinder where there are flammable liquids,
solids or gases, such as paint solvents, etc.
DO NOT
allow children to operate the grinder.
DO NOT
operate the grinder if any parts are missing as this
may cause failure or possible personal injury.
DO NOT
hold unsecured workpiece in your hand.
DO NOT
carry the grinder with your finger on the power trigger.
DO NOT
use the grinder for a task it is not designed to perform.
DO NOT
operate the grinder when you are tired or under the
influence of alcohol, drugs or intoxicating medication.
DO NOT
get the grinder, battery or charger wet or use in damp
or wet locations.
Keep the grinder, battery and charger in a safe, dry, childproof
area where the temperature will not exceed 104°F (40°C).
1.2 ELECTRICAL SAFETY.
REGARDING DIRECT MAINS POWER USE WITH THE
CHARGING BASE AND PLUG ONLY.
WARNING!
It is the owner’s responsibility to read, understand
and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the
installation of appropriate safety devices. An RCCB (Residual
Current Circuit Breaker) should be incorporated in the main
distribution board. We also recommend that an RCD (Residual
Current Device) is used with all electrical products, particularly
portable equipment which is plugged into an electrical supply
not protected by an RCCB.
You must
also read and understand
the following instructions concerning electrical safety.
•
The Electricity At Work Act 1989 requires all portable
electrical appliances, if used on business premises, to be
tested by a qualified electrician, using a Portable
Appliance Tester (PAT), at least once a year.
•
The
Health & Safety at Work Act 1974
makes owners of
electrical appliances responsible for the safe condition of the
appliance, and the safety of the appliance operator.
If in any
doubt about electrical safety, contact a qualified electrician
•
Battery Charger Safety Instructions
WARNING!
DO NOT
use the charging base to charge any
battery other than that required for the tool. Other types of
batteries may explode!
Inspect the plug, cable and the charging base for wear
and damage to ensure items are safe before connecting to the
mains power supply. If worn or damaged
DO NOT
use,
immediately replace, or contact a qualified electrician.
Check cables are always protected against short circuit and
overload.
Uncoil the power cable between the plug and the charging base
before use.
DO NOT
pull or carry the charging base by the charger power
lead, or pull the plug from the mains socket by the power lead.
DO NOT
use any other type of transformer with the charging
base.
DO NOT
try to open or dis-assemble the plug or charging base.
DO NOT
use the plug to power any other electrical item.
Disconnect the charging base from the mains power supply
when not in use.
DO NOT
expose the charging base to damp or wet conditions
(for indoor use only).
DO NOT
operate the charging base if it has been dropped, or
has received a sharp knock, or is damaged. Contact an
authorised service agent.
DO NOT
dismantle the charging base as this may cause
damage or personal injury and will invalidate your warranty.
DO NOT
insert foreign objects or material into the slot
reserved for the battery.
DO NOT
immediately charge a second battery. Consecutive
charging will overheat the charging base. Allow the unit to cool
for 15 minutes before charging the next battery.
Ensure that the insulation on all cables and on the appliance is
safe before connecting it to the power supply.
Ensure that cables are always protected against short circuit
and overload.
DO NOT
use worn or damaged cables, plugs or connectors.
Immediately have any faulty item repaired or replaced by a
qualified electrician.
1.3 BATTERY SAFETY INSTRUCTIONS.
WARNING! Battery contains Lithium-ion which is dangerous.
Handle with care to avoid damage, fire, corrosion or personal
injury.
Charge battery prior to its first use. The battery will have been
shipped in a low charge state.
To reduce the risk of burns or fire:
DO NOT
Attempt to open, disassemble, modify or service the
battery pack.
DO NOT
Crush, puncture, short external contacts or dispose of
in fire or water.
DO NOT
Expose to temperatures above 40°C (104°F).
Replace only with the battery pack designated for this product.
Use only the charging base provided to charge the drill
battery.
DO NOT
attempt recharging the battery by means of an engine
generator or a DC power source.
WARNING! Dispose of spent batteries correctly as they contain
Lithium-ion.
DANGER!
DO NOT
attempt to disassemble the
1. SAFETY INSTRUCTIONS
INSTRUCTIONS FOR:
CORDLESS LITHIUM-ION ANGLE
GRINDER Ø115
MM
18V 1HR CHARGE
- 2 BATTERIES
MODEL N
O
:
CP5418V
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT
:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
Original Language Version
CP5418V Issue: 2(L) - 21/02/14
© Jack Sealey Limited
