![background image](http://html1.mh-extra.com/html/sealey/cp400li/cp400li_instructions_1225000001.webp)
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1.
GENERAL SAFETY
9
Follow all workshop safety rules, regulations and conditions when using the wrench.
9
Remove the battery pack from the wrench before servicing or performing any maintenance.
9
Maintain the wrench and battery pack in good condition. Check moving parts for alignment on a regular basis.
9
Replace or repair damaged parts.
Use an authorised service agent and recommended parts only. Unauthorised parts may be dangerous
9
and will invalidate the warranty.
9
Ensure the wrench is locked before installing the battery pack.
9
Keep the wrench, battery pack and charger clean for optimum performance.
9
Keep the work area clean and tidy and free from unrelated materials. Ensure that there is adequate lighting.
9
Ensure that battery pack is correctly inserted into the wrench handle and latched in place before operating wrench.
WARNING!
When working around vehicle brake systems we recommend that you wear suitable respiratory protection owing to the
possible Presence of asbestos dust from brake linings.
8
Use only impact sockets which are specifically designed for use with an impact wrench.
8
Avoid unintentional starting.
8
Wear approved safety eye/face shield, ear defenders and hand protection.
8
Remove ill-fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
8
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
8
Keep children and unauthorised persons away from the work area.
8
DO NOT
operate the wrench if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT
use the wrench unless you have been instructed in its use by a qualified person.
8
DO NOT
operate the wrench where there are solvent fumes or flammable gases, liquids or solids.
8
DO NOT
leave the wrench operating unattended.
8
DO NOT
carry wrench with your finger on the trigger. Keep direction switch in ‘locked’ position when not in use.
8
DO NOT
use the wrench for a task it is not designed to perform.
8
DO NOT
operate the wrench when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
get the wrench or battery charger wet or use in damp or wet locations.
9
Keep wrench and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 40°C (104°F).
1.2.
BATTERY SAFETY INSTRucTIONS
9
Charge the battery pack prior to first use. The battery pack will have been shipped in a low charge state.
9
Use only the charger provided to charge the battery pack.
8
DO NOT
charge the battery pack when room temperature is below 10°C (50°F) or above 40°C (104°F).
8
DO NOT
attempt recharging the pack by means of an engine generator or a DC power source.
8
DO NOT
short-circuit the battery pack by touching both terminals at the same time with a metal object, or your fingers etc.
8
DO NOT
store battery pack or wrench in locations where the temperature may exceed 40°C (104°F).
1.3.
MAINS POWER ELEcTRIcAL SAFETY
(In relation to the battery charger)
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.3.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.3.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.3.3.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualified electrician.
1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Original Language Version
© Jack Sealey Limited
Refer to
instructions
cORDLESS IMPAcT WRENch 18v 3Ah LI-ION
1/2” SquARE DRIvE
MoDEL no’s:
cP400LI,
cP400LIhv
Wear ear
protection
Wear eye
protection
Wear
protective
gloves
Wear a mask
Wear
protective
footwear
CP400LIHV Issue 1 26/11/19