1.1. GENERAL SAFETY
Maintain the
screwdriver in good condition. Check moving parts alignment on a regular basis.
Keep the screwdriver and charger clean for best and safest performance.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
Secure loose workpieces with a clamp, vice or other adequate holding device.
Avoid unintentional starting.
Wear approved safety eye protection.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Be aware that this screwdriver does not need to be plugged into the mains power.
Keep children and unauthorised persons away from the working area.
DO NOT
allow children to operate the screwdriver.
DO NOT
hold unsecured workpiece in your hand.
DO NOT
carry the screwdriver with your finger on the trigger.
DO NOT
use the screwdriver for a task it is not designed for.
DO NOT
operate the screwdriver when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
get the screwdriver or battery charger wet or use in damp or wet locations.
Keep screwdriver and charger in a safe, dry, child proof area where the temperature will not exceed 104°F (40°C).
1.2. ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING SCREWDRIVER TO THE POWER SUPPLY.
WARNING!
It is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current
Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device)
is used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an
RCCB.
You must
also read and understand the following instructions concerning electrical safety.
1.2.1.
The Electricity At Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2.
The Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of the
appliance and the safety of the appliance operator.
If in any doubt about electrical safety, contact a qualified electrician.
1.2.3.
You must ensure that you:
Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power
supply. If worn or damaged
DO NOT
use.
Important:
Check that the voltage marked on the charger plug is the same as the power supply to be used.
DO NOT
pull the charger plug from the mains socket by the lead.
DO NOT
use any other type of charger with this product.
DO NOT
try to take the charger plug apart.
DO NOT
use the charger plug to charge or power any other electrical item.
DO NOT
get the charger wet, or use in wet, damp conditions (for indoor use only).
WARNING!
NEVER
substitute a standard 13amp 3 pin plug, or any other type of plug, for the charger plug.
1.3. BATTERY SAFETY
WARNING!
To reduce the risk of burns or fire:
DO NOT
attempt to open, disassemble, modify or service the battery pack.
DO NOT
crush, puncture, short external contacts or dispose of in fire or water.
DO NOT
expose to temperatures above 60°C (140°).
Recycle or dispose of used battery as stipulated by local regulation.
1. SAFETY INSTRUCTIONS
InSTRuCTIonS FoR:
3.6V LI-ION CORDLESS
SCREWDRIVER SET - 46pC
MoDEL no:
Cp36S
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,
give you years of trouble free performance.
IMPORTANT
:
pLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OpERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS. USE
THIS pRODUCT CORRECTLY, AND WITH CARE FOR THE pURpOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
pERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
2. INTRODUCTION AND SpECIFICATION
Powerful lightweight screwdriver featuring locking swivel adjustment from pistol to straight type. Forward, reverse and trigger-lock
control. Adjustable torque with up to 6 settings. 6mm quick-release bit holder. Integral LED light to illuminate working area. Powered
by a lithium-ion battery which maintains a high energy density level and has no memory effect, lasting for longer periods of time
than traditional ni-Cd cells and will recover from a deep discharge state with no tendency to reduce overall capacity. Three LED's
indicate battery life. Soft-grip handle for comfort and control. Supplied in a carry-case with accessories.
No-Load Speed: . . 0-200rpm
Maximum Torque: 3.5Nm
Noise power . . . . . 62dB.A
Charging Time:. . . 3-5 Hours
Noise pressure . . . 72dB.A
Contents:
Charging unit, Magnetic Bit Holder, Socket Adaptor.
Screwdriver Bits: Slotted - 3, 4, 5, 6, 7mm, Phillips - #0, #1, #2, #3, Pozi - #0, #1, #2, #3, Hex - 2, 2.5, 3, 3.5, 4, 5, 6mm
TRX - T10, T15, T20, T25, T27, T30, T40, T45, Sockets - 6, 7, 8, 9, 10, 11, 12, 13mm, 55mm.
Screwdriver Bits: Slotted - 4, 6mm, Phillips - #0, #2, Drill Bits - 1.5, 3mm.
Original Language Version
CP36S Issue: 3 - 13/01/12
