18V 1.5AH CORDLESS RIVETER
MODEL No:
CP313X
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING!
Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this
equipment.
9
Familiarise yourself with the applications, limitations and potential hazards peculiar to the riveter.
9
Maintain the
riveter in good condition (use an authorised service agent).
9
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Keep the work area clean, uncluttered and ensure that there is adequate lighting.
9
Keep the riveter clean for best and safest performance.
WARNING!
Always wear approved eye or face protection when operating the riveter.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain, and/or tie back, long hair.
9
Keep the riveter away from your body and at a safe distance from others.
9
Keep children and unauthorised persons away from the work area.
9
Secure unstable workpiece with a clamp, vice or other adequate holding device.
9
Ensure that spent rivet stems are disposed of correctly and do not cause a hazard.
8
DO NOT
use the riveter for any purpose other than that for which it is designed.
8
DO NOT
get the riveter wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT
allow untrained persons to operate the riveter.
8
DO NOT
point or fire the riveter at people or animals.
8
DO NOT
operate the riveter when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
operate the riveter in a flammable or explosive atmosphere.
1.1.
ELECTRICAL SAFETY
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) onlyare marked with the Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
8
DO NOT
connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
BATTERY CHARGER SAFETY INSTRUCTIONS
WARNING! DO NOT
attempt to charge any battery other than that supplied for the product.
Other types of batteries may explode!
9
All mains electrical supply safety features must be followed as described in above.
9
Disconnect the charger from the mains supply when not in use.
8
DO NOT
charge battery if room temperature is below 10°C (50°F) or above 40°C (104°F).
Refer to
instruction
manual
Wear eye
protection
Wear ear
protection
Original Language Version
© Jack Sealey Limited
CP313X Issue:1 13/07/20
Recommended fuse rating
3 Amp
