CORDLESS HOT AIR GUN 20V - BODY ONLY
MODEL NO:
CP20VHG
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL SAFETY.
9
Disconnect the gun from the battery unit before changing accessories, servicing or performing any maintenance.
9
Maintain the gun and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
9
Ensure the gun is switched off before installing the battery pack.
9
Keep the gun and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the multi-tool e.g. ceilings, floors and enclosures may contain electrical items or water piping.
9
Ensure battery pack is correctly inserted into the tool handle and latched in place before attempting to switch it on.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Keep children and unauthorised persons away from the working area.
9
Keep tool and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).
8
DO NOT
use the tool where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT
allow children to operate the tool.
8
DO NOT
operate the tool if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT
obstruct the air flow by blocking or covering the air outlet.
8
DO NOT
touch the nozzle during or after use as it becomes extremely hot.
8
DO NOT
use the tool in rain or a wet environment, or areas of high humidity and damp (i.e. bathrooms, steam rooms etc.).
8
DO NOT
direct the hot air flow at yourself, others, animals or plants.
8
DO NOT
use the tool in combination with chemical strippers.
8
DO NOT
hold unsecured work piece in your hand.
8
DO NOT
leave the tool operating unattended.
8
DO NOT
carry the tool with your finger on the power switch.
8
DO NOT
use the tool for a task it is not designed to perform.
8
DO NOT
operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
▲
DO NOT
use the tool as a hair dryer.
WARNING:
The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and
8
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product,
8
but must be applied by the operator.
1.2.
LEAD PAINT WARNING!
Paint once contained lead as a traditional ingredient. Paint particles, resulting from the removal of such paint,
are toxic and ingestion/inhalation must, therefore, be avoided. The following action must be taken before using this tool:
The user must determine potential hazard relating to age of paint to be removed (modern paints do not have lead content).
▲
DANGER!
Keep all persons and pets away from the work area. The following are particularly vulnerable to the effects of lead paint dust:
expectant women, babies and children. We recommend personal protection by using the following safety items: Paint Spray Respirator
(Sealey ref. SSP1699), PE Coated Hooded Coverall (Sealey ref. SSP267), Latex Gloves (Sealey ref. SSP24).
Take adequate measures to contain the paint dust, flakes, and scrapings. When task is complete continue to wear safety equipment
and thoroughly clean all areas. Ensure paint waste is disposed of in sealed bags or containers.
2.
i
INTRODUCTION
The 20V Series has been designed to suit users from the DIY enthusiast to the professional. These body only tools offer a one battery
fits all solution with a choice of 20V lithium batteries ranging from 2Ah to 4Ah, meaning costs can be kept down whilst quality remains
high. Quality, stylish, lightweight tools with durable composite housing and a soft grip making them comfortable and easy to use.
Refer to
instruction
manual
Wear eye
protection
Wear protective
gloves
CP20VGH Issue 1 21/05/19
Original Language Version
© Jack Sealey Limited
Warning:
Hot surface
