INSTRUCTIONS FOR:
24V CORDLESS HAMMER DRILL
Model:
CP2024VHK
Thank you for purchasing a Sealey product. Manufactured to a high standard this article will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
1.2. BATTERY SAFETY INSTRUCTIONS
p
WARNING!
The battery contains nickel-cadmium which is dangerous and must therefore be handled with care to avoid damage, fire,
corrosion or personal injury.
3
Charge battery pack prior to first use. The battery pack will have been shipped in a low charge state.
3
Use only the provided charger to charge the battery pack.
7
DO NOT
charge battery pack when the room temperature is below 50
O
F (10
O
C) or above 104
O
F (40
O
C).
7
DO NOT
attempt to recharge the battery pack by means of an engine generator or a DC power source.
7
DO NOT
short-circuit the battery by touching both terminals with a metal object, or your fingers etc.
7
DO NOT
store the battery pack (or drill) in locations where the temperature may exceed 104
O
F (40
O
C), such as outside sheds, above heaters,
or metal buildings in summer.
p
WARNING!
Dispose of spent batteries correctly as they contain nickel-cadmium.
s
DANGER! DO NOT
attempt to disassemble the battery
pack. For safety and environmental reasons
DO NOT
discard in domestic waste, or by burning.
ONLY
discard or recycle according to local
waste authority regulations.
p
WARNING! DO NOT
allow a leaking battery to contact your person. If you come into contact with battery liquid take the following
action immediately:
p
a) Skin contact:
Wash immediately with soap and water, then wash in either lemon juice or vinegar.
p
b) Eye contact:
Wash with a strong solution of boric acid, and seek immediate medical attention.
1.3. MAINS POWER ELECTRICAL SAFETY (In relation to the battery charger)
p
p
p
WARNING! It is the users responsibility to check the following:
You must
check all electrical equipment and appliances to ensure they are safe before using.
You must
inspect power supply leads,
plugs and all electrical connections for wear and damage.
You must
ensure the risk of electric shock is minimised by the installation
of appropriate safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board.
We recommend that an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use an RCD
with portable products that are plugged into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician.
You may obtain a Residual Current Device by contacting your dealer.
You must
also read and understand the following instructions
concerning electrical safety.
1.3.1. The
Electricity At Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a qualified
person, using a Portable Appliance Tester (PAT), at least once a year.
1.3.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator.
If in any doubt about electrical safety, contact a qualified electrician.
1.3.3.
DO
ensure that the insulation on all cables and the product itself is safe before connecting to the mains power supply. See 1.3.1. above
and use a Portable Appliance Tester (PAT).
1.3.4.
DO
ensure that cables are always protected against short circuit and overload.
CP2024VHK - 0064 - (1) - 240401
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.1.
GENERAL SAFETY
3
Disconnect the drill from the battery unit before changing accessories, servicing or performing any maintenance.
3
Maintain the drill and battery pack in good condition. Check moving parts alignment on a regular basis.
3
Replace or repair damaged parts.
Use an authorised service agent and recommended parts only. Unauthorised parts may be dangerous
and will invalidate the warranty.
3
Ensure the drill is switched off before installing the battery pack.
3
Keep the drill, battery pack and charger clean for best and safest performance.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Evaluate your work area before using the drill i.e. ceiling, floors and enclosures may contain electrical items or water piping.
3
Ensure battery pack is correctly inserted into the drill handle and locked in place before attempting to switch drill on.
3
Secure non-stable workpiece with a clamp, vice or other adequate holding device.
DO NOT
hold
workpiece in your hand.
3
Avoid unintentional starting.
3
Wear approved safety eye protection (standard spectacles are not adequate).
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Be aware that this drill does not need to be plugged into the mains power.
3
Keep chuck direction switch in the locked position until the drill is required for use.
3
Keep children and unauthorised persons away from the work area.
7
DO NOT
use the drill where there are flammable liquids, solids or gases such as paint solvents, etc.
7
DO NOT
allow children to operate the drill.
7
DO NOT
operate the drill if any parts are missing as this may cause failure and/or personal injury.
7
DO NOT
leave the drill operating unattended.
7
DO NOT
carry the drill with your finger on the power switch. Keep chuck direction switch in the locked position.
7
DO NOT
use the drill for a task which it is not designed to perform.
7
DO NOT
operate the drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT
get the drill or battery charger wet or use in damp or wet locations.
3
Keep drill and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 104
O
F (40
O
C).
