HEATING TORCH BUTANE MICRO
mODEL NO:
AK4041
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using
this equipment.
WARNING!
Always wear approved eye / face protection when operating the torch.
WARNING!
Butane gas is extremely flammable, handle with care. Follow instructions on butane re-filler can when refilling.
WARNING!
Always point the torch away from the eyes and body when igniting and during operation.
WARNING!
Ensure the flame is completely extinguished after use.
WARNING!
Only use in a well ventilated area.
8
DO NOT
use the torch in an area where paint fumes, solvents or other flammable solids, liquids or gases pose a potential hazard.
9
Keep flammable material away from the torch when operating.
8
DO NOT
operate the torch when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
hold any work piece by hand.
8
DO NOT
touch the work piece close to the heated area as it will be very hot. Allow to cool.
8
DO NOT
operate the torch if it is damaged as this may cause failure and/or possible personal injury.
8
DO NOT
touch the top of the torch during or immediately after use, as it will be very hot. Allow to cool.
8
DO NOT
leave the torch operating unattended.
8
DO NOT
use this torch continuously for longer than 5 minutes.
8
DO NOT
allow children to operate the torch.
9
After use, allow the torch to cool before storing it.
9
When not in use, store away from direct sunlight in a safe, dry,
childproof location.
2. INTRODUCTION
Stylish design with piezo ignition. Produces a flame of approximately 1300°C.
Powered by Butane (lighter fluid) and when full can produce a flame for up to
30 minutes (not to be used continuously for more than five minutes). Suitable
for use in extreme weather conditions. Ideal for soft soldering, camping,
household repairs and a variety of general purpose uses. Supplied with key
chain.
3. SpECIFICATION
model no ...................................................................
AK4041
Weight .........................................................................
0.04kg
4. OpERATION
4.1.
FILLING
4.1.1.
Allow to cool before refilling.
4.1.2.
Turn the torch so that the filling valve (fig.1) is facing upwards. Press nozzle of Butane fuel re-filler can into filling valve and fill torch
until at least ¾ full. Allow fuel to warm for 5 minutes before use.
4.2.
USE
4.2.1.
Flip up the Flame Nozzle Cover (fig.1A) and slowly push down on the Ignition Button (fig.1B) and keep holding it down.
4.2.2.
To adjust flame, use the Flame Adjuster in the base (see fig.1C for direction of adjustment).
Note:
If the adjuster is left set too high or too low, the torch may not re-light next time, so re-set after use.
4.2.3.
To turn off, release the Ignition Button. Close the Flame Nozzle Cover to protect the nozzle.
Note:
The cover is
NOT
designed to turn off the flame,
DO NOT
close it when the flame is still lit.
8
DO NOT
use continuously for more than 5 minutes. Allow to cool for a minute before re-lighting.
.
Refer to
instruction
manual
Wear eye
protection
A
K4041 | Issue:2 (H,F) 30/10/18
Original Language Version
© Jack Sealey Limited
fig.1
