IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
Refer to instruction
manual
TROLLEY JACK 4TONNE ROCKET LIFT
PART NO:
4040A.V2 SERIES
Wear safety
footwear
1. SAFETY
9
Ensure the jack is in sound condition and good working order. Take action for immediate repair or
replacement of damaged parts. Use genuine parts only. The use of improper parts may be dangerous
and will invalidate the warranty.
9
Locate the jack in a suitable, well lit working area.
9
Keep working area clean and tidy and free from unrelated materials.
9
Use jack on level and solid ground, preferably concrete.
9
Avoid tarmacadam as jack may sink in. Chock wheels of vehicle.
9
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear
(or “PARK” if automatic).
9
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow
for vehicle tilting.
9
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
9
Ensure there are no passengers in the vehicle.
9
Place jack under only those lifting points recommended by vehicle manufacturer (see vehicle handbook).
9
Check that the lifting point is stable and centred on the jack saddle.
9
Ensure the jack wheels are free to move and that there are no obstructions.
▲
DANGER:
Use the jack for lifting only,
NOT
for supporting the lifted load.
9
Ensure there are no persons or obstructions beneath the vehicle before lowering.
9
Use suitable axle stands under the vehicle before proceeding with any task.
9
Use a qualified person to lubricate and maintain the jack.
9
Ensure that only hydraulic jack oil is used in the jack.
8
DO NOT
operate the jack if damaged.
8
DO NOT
allow untrained persons to operate the jack.
8
DO NOT
exceed the rated capacity of the jack.
8
DO NOT
allow the vehicle to move during lifting or lowering, or use the jack to move the vehicle.
8
DO NOT
jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8
DO NOT
work under the vehicle until appropriately rated axle stands have been correctly positioned.
8
DO NOT
use the jack for purposes other than that for which it is intended.
8
DO NOT
top up hydraulic system with brake fluid. Use hydraulic jack oil only.
8
DO NOT
adjust the safety overload valve.
9
When not in use store jack, fully lowered, in a safe, dry, childproof area.
2. INTRODUCTION
Heavy base design and large jacking saddle for increased load stability. Universal joint release mechanism allows safer, more controlled
lowering of the jack. Rocket Lift feature brings lifting arm into contact with jacking point with minimal pumps. Polyurethane wheels for
smoother manoeuvrability and helps prevent damage to workshop floor. Magnetic wheel nut retention tray. Protective jack handle sleeve helps
prevent accidental damage to car bodywork when pumping the handle. The range is available in five colours. 2 Year warranty - 2nd year subject to
T & C’s and registration on website (www.sealey.co.uk).
3. SPECIFICATION
Model Nos: ............................................... 4040A.V2 SERIES
Capacity ...................................................................... 4tonne
Minimum saddle height .............................................. 100mm
Maximum saddle height ............................................. 533mm
Maximum chassis height ............................................ 162mm
Length ........................................................................ 751mm
Weight ......................................................................... 43.5kg
4. ASSEMbLY
ASSEMBLY
4.1.
Insert the upper handle into the lower handle. Secure the two pieces together with the bolt (Fig.1.A).
4.2.
Undo the handle socket screw (B) until it no longer protrudes into the handle socket (Fig.2).
4.3.
Insert the pump handle into the handle socket, engaging the square drive of the release valve.
4.4.
Ensure that the handle is correctly inserted into the socket, then tighten the handle socket screw (B).
Fig.1
4040A.V2 Series Issue:1 - 04/12/18
Original Language Version
© Jack Sealey Limited
