Seagull Models T-6A Texan II Assembly Manual Download Page 1 | Manualshive

Page: 1 / 26

background image

Made in Vietnam.

Specifications:

Wing span--------------------------------------------- 63.0 in -------------------------------------------- 160cm.
Wing area--------------------------------------- 644.5sq.in -------------------------------------- 41.6 sq.dm.
Approximate flying weight------------------------ 9.3 lbs -------------------------------------------- 4.2 kg.
Length-------------------------------------------------- 58.1in ----------------------------------------- 147.5cm.
Recommended engine size----------------.75-.91cu.in ----------------------------------------- 2-stroke.
.91-1.00cu.in ------------------------------------ 4-stroke.

ELECTRIC CONVERSION : OPTIONAL.
Recommended R/C --------------------------------------------- 4 channels with 7 servos.
Flying skill level ---------------------------------------------------- Advanced/Intermediate.

Kit features.

•

Ready-made—minimal assembly & finishing required.

•

Ready-covered—including decals, trim & covering.

•

Factory-installed pushrod.

•

Photo-illustrated step-by-step Assembly Manual.

MS: SEA 103-USA

“Graphics and specifications may change without notice”.

ASSEMBLY MANUAL

T-6A Texan II

1
2
3
...
»

Summary of Contents for T-6A Texan II



























Reviews:

No comments

Related manuals for T-6A Texan II

Brand: Old School Model Works Pages: 20

Brand: LEGO Pages: 64

Brand: E-FLITE Pages: 21

Brand: Dancing Wings Hobby Pages: 2

Brand: Odyssey Pages: 2

Brand: Beyblade Pages: 2

LENGMOOS STATION

Brand: Faller Pages: 12

Brand: marklin Pages: 32

KOKUYO Flair Klixi Mixi

Brand: PREZIOSI Pages: 6

Brand: C&C Models Pages: 23

Brand: E-FLITE Pages: 20

Brand: marklin Pages: 24

NUM NOMS 547334

Brand: MGA Entertainment Pages: 2

Brand: Aeronaut Pages: 4

Magic Formula 3D ARF

Brand: Model Tech Pages: 48

Brand: marklin Pages: 44

Brand: REVELL Pages: 9

OLD-TOWN TOWER WITH WALL 232171

Brand: Faller Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands