manualshive.com logo in svg

Seagull Models Sparrow Hawk SEA-93, Instruction Manual, Page: 1 / 22

Share
Download
Seagull Models Sparrow Hawk SEA-93 Instruction Manual Download Page 1

Made in Vietnam.

ASSEMBLY MANUAL

MS: SEA 93

“Graphics and specfications may change without notice”.

Kit features.

•

Ready-made—minimal assembly & finishing required.

•

Ready-covered covering.

•

Photo-illustrated step-by-step Assembly Manual.

     Specifications

Wingspan----------------------------------- 63 in ---------------------------------- 160cm.
Wing area------------------------------------746.6 sq.in ------------------- 48.2 sq.dm.
Approximate flying weight--------------7.9-8.8 lbs --------------------------3.6-4kg.
Length--------------------------------------- 54.7 in -------------------------------- 139cm.
Recommended engine size----------.0.61 -0.75 cu.in -------------------2-stroke.
                                                            1.00-1.10   cu.in ----------------- 4-stroke.
ELECTRIC CONVERSION : OPTIONAL.
Radio  System  required 4 channels  with 6  servos.
Flying skill level  Intermediate/advanced.

SPARROW HAWK

Summary of Contents for Sparrow Hawk SEA-93























Reviews:

No comments