Seagull Models Magic Star 3D EP Assembly Manual Download Page 1 | Manualshive

Page: 1 / 22

background image

WWW.SEAGULLMODELS.COM

1

A S S E M B LY M A N UA L

Code: SEAX157

www.seagullmodels.com

“ Graphics and specifications may change without notice “ .

MAGIC STAR 3D ELECTRIC POWER

wingspan 39”

Specifications:
Wingspan---------------39 in (99.1 cm).
Wing area---------------432.5 sq.in (27.9 sq.dm).
Weight-------------------1.5-1.9 lbs (0.7-0.85 kg).
Length-------------------33.8 in (85.8 cm).
Motor size---------------450-180 size brushless
----------------------------30-amp brushless ESC
Radio---------------------4 channels with 4 sub -micro servos.

1
2
3
...
»

Summary of Contents for Magic Star 3D EP























Reviews:

No comments

Related manuals for Magic Star 3D EP

Brand: U.S. Brig Pages: 40

Brand: Fisher-Price Pages: 16

Brand: Minicraft Models Pages: 4

Little Learning Pal

Brand: VTech Pages: 16

Brand: H-KING Pages: 15

4-6-2 Pacific Steam Locomotive

Brand: Rail King Pages: 29

Branchline Class 03

Brand: Bachmann Pages: 3

Brand: Jamara Pages: 16

NUMBER FLASH CARDS 77824

Brand: Fisher-Price Pages: 12

Brand: Dancing Wings Hobby Pages: 2

PowerTouch Baby H8052

Brand: Fisher-Price Pages: 12

RC flying dragon

Brand: goliath Pages: 8

Brand: LEXIBOOK Pages: 27

Brand: Our Generation Pages: 2

WM.com_AWH096_057E

Brand: MD SPORTS Pages: 6

Brand: REVELL Pages: 10

Brand: West Michigan Park Flyers Pages: 14

Weekend Edition Spitfire Mk.IXe

Brand: Eduard Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands