background image

Seagate Video 3.5 HDD Product Manual, Rev. A

19

2.12.3 FCC verification

These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an

 

external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the

 

customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required.

Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive, 
motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 
15 of the FCC rules. Operation with non-certified assemblies is likely to result in interference to radio and television

 

reception.

Radio and television interference.

 This equipment generates and uses radio frequency energy and if not installed and

 

used in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.

This equipment is designed to provide reasonable protection against such interference in a residential installation. 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

 

interference to radio or television, which can be determined by turning the equipment on and off, users are encouraged to

 

try one or more of the following corrective measures:

• Reorient the receiving antenna.

• Move the device to one side or the other of the radio or TV.

• Move the device farther away from the radio or TV.

• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.

If necessary, users should consult the dealer or an experienced radio/television technician for additional suggestions. 
Users may find helpful the following booklet prepared by the Federal Communications Commission: 

How to Identify and

 

Resolve Radio-Television Interference Problems

. This booklet is available from the Superintendent of Documents, 

U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4.

2.13

Environmental protection

Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting

 

certain chemical substances.

2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive

The European Union Restriction of Hazardous Substances (RoHS) Directive, restricts the presence of chemical substances, 
including Lead, Cadmium, Mercury, Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. This 
drive is manufactured with components and materials that comply with the RoHS Directive.

Summary of Contents for ST8000VM004




































Reviews: