SeaDoo Rotax 1503 4-Tec 2005 Page 74 Engine Shop Manual Download

Page: 74 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 05 (COOLING SYSTEM)

Installation

The installation is the opposite of the removal pro-
cedure. Pay attention to the following details.

NOTE:

Never use oil in the press fit area of the oil

seal and rotary seal.

Push coolant pump shaft oil seal in place by using
thumb.

Install the new rotary seal using the rotary seal
installer (P/N 529 035 823).

529035823

CAUTION:

Never use a hammer for the rotary

seal or water/oil pump shaft installation. On-
ly use a press to avoid damaging the ceramic
component.

F18E19A

1. Rotary seal
2. Rotary seal installer

Install the coolant/oil pump shaft using the rotary
seal installer (P/N 529 035 823) on the opposite
side to the rotary seal and the oil seal protector
(P/N 529 035 822) with a press.

F18E1AA

1. Oil seal protector
2. Coolant/oil pump shaft

F18E1BA

1. Coolant/oil pump shaft with oil seal protector
2. Rotary seal installer

smr2005-088

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands