SeaDoo Rotax 1503 4-Tec 2005 Engine Shop Manual Download Page 71

Page: 71 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 05 (COOLING SYSTEM)

F18E11A

1. Weep hole pump housing gasket

Check if thermostat is in good condition. Refer to
THERMOSTAT elsewhere in this section.

Installation

The installation is the opposite of the removal pro-
cedure. Install screws as per the following illus-
tration.

F18E10A

1. Screws M6 x 25
2. Screws M6 x 105

CAUTION:

To prevent leaking, take care that the

gaskets are exactly in groove when you rein-
stall the coolant pump housing.

Apply Loctite 243 (P/N 290 897 651) on screw
threads and torque to 10 N•m (89 lbf•

Tightening sequence for screws on coolant pump
housing is as per following illustration.

F18E10B

COOLANT PUMP IMPELLER

Removal

Remove:
– coolant pump

no. 6

as described in this section

– unscrew the impeller

no. 8

clockwise.

F18E13A

1. Impeller

CAUTION:

Coolant/oil pump shaft no. 9 and im-

peller no. 8 have left-hand threads. Remove by
turning clockwise and install by turning coun-
terclockwise.

Inspection

Check impeller for cracks or other damage. Re-
place impeller if damaged.

Installation

The installation is the opposite of the removal pro-
cedure. Pay attention to the following details.

smr2005-088

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands