SeaDoo Rotax 1503 4-Tec 2005 Page 47 Engine Shop Manual Download

Page: 47 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 03 (PTO HOUSING AND MAGNETO)

R1503motr54B

TYPICAL

1. Location pin
2. Location pin holes

Apply Loctite 243 (P/N 293 800 060) on threads.
Torque rotor screws to 24 N•m (17 lbf•ft).

STARTER DRIVE ASS'Y

Removal

Remove:
– PTO housing and ring gear as described above
– starter drive ass'y

no. 8

R1503motr55A

TYPICAL

1. Starter drive ass'y

CAUTION:

Be careful not to lose the distance

washer, disc springs no. 6 and washer no. 7
located on the starter drive shaft.

smr2005-034-002_a

TYPICAL

1. Disc springs
2. Washer
3. Starter drive gear

Inspection

Check condition of the teeth, shaft, etc. and if the
sprag clutch operates well. If damaged, replace
faulty part.

Installation

For installation, reverse the removal procedure.
However, pay attention to the following.

NOTE:

When installing a new starter drive ass’y,

oil the shaft and threads of the gear with engine
oil.

Apply some Isoflex Topas NB52 grease (P/N 293
550 021) on the starter drive bearing located in the
cylinder block and on the starter drive support in
the PTO housing cover.

smr2005-032

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands