SeaDoo Rotax 1503 4-Tec 2005 Engine Shop Manual Download Page 44

Page: 44 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 03 (PTO HOUSING AND MAGNETO)

Installation

Reinstall removed parts in the reverse order.

CAUTION:

When installing PTO seal on super-

charged engines, make sure to position the
Oetiker clamps as shown in the picture.

R1503motr367A

1. Oetiker clamps

COUPLING

Removal

Lock crankshaft with locking tool (P/N 529 035
821). Refer to CYLINDER BLOCK section.

Remove:
– PTO seal as described above
– coupling

no. 12

using impeller remover/installer

(P/N 529 035 820).

529035820

CAUTION:

Apply some oil on the tool to protect

the seal located in the PTO coupling.

R1503motr48A

TYPICAL

Inspection

Check if seal

no. 13

is brittle, cracked or hard.

Check coupling for worn splines.

If damaged, replace faulty part.

R1503motr49A

Installation

For installation, reverse the removal procedure.
However, pay attention to the following.

Torque PTO coupling to 250 N•m (184 lbf•ft). Ap-
ply Loctite anti-seize (P/N 293 800 070) on threads.

STATOR

Removal

Remove:
– PTO housing (refer to PTO HOUSING RE-

MOVAL elsewhere in this section)

– holding plate

no. 14

with CPS

no. 15

smr2005-032

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands