SeaDoo Rotax 1503 4-Tec 2005 Engine Shop Manual Download Page 11

Page: 11 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 01 (LEAK TEST)

LEAK TEST

SERVICE TOOLS

Description

Part Number

Page

Drive shaft adapter ............................................................... 529 035 892 ............................................. 2
Drive shaft adapter ............................................................... 529 035 985 ............................................. 2

SERVICE PRODUCTS

Description

Part Number

Page

Molykote 111........................................................................ 413 707 000 ............................................. 4

PROCEDURES

PREPARATION

The procedure has to be done when engine op-
erating temperature of approx. 70°C (158°F) is
reached.



WARNING

Prevent burning yourself due to handling on
the hot engine.

Remove:
– any parts to have access to engine
– safety lanyard



WARNING

Safety lanyard must be removed to prevent
engine to be cranked while fuel rail is re-
moved to prevent fuel to be sprayed out.
Fuel is flammable.

– jet pump (refer to JET PUMP in the appropriate

VEHICLE SHOP MANUAL

)

– coolant tank cap



WARNING

To prevent burning yourself only remove the
coolant tank cap by wearing the appropriate
safety equipment.

– oil dipstick

R1503motr153A

1. Oil dipstick

– Unplug ignition coil and pull it out
– spark plug.

NOTE:

Ignition coil may be used as an extractor.

SMR2005-032

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands