SEA ISUZU FSR Owner'S Manual Download Page 39

Page: 39 / 56

OWNER

’

S MANUAL

(

SEA ISUZU FSR/FSD EV)

SEA-OWS-QA-004/5

ISSUE DATE:

30/05/2020

Page

11- Trouble Shooting Guide

Caution:

Under no circumstances are users to carry out work on high voltage components. This must only be
done by a SEA-Electric technician.

•

The vehicle does not start

Fault diagnosis

Handling methods

12/24v start battery has gone flat

Charge or replace the battery

Isolator switch is in off position

Cycle switch

and ensure it is firmly in the ‘On’

position

Ensure handbrake is on and brake pedal is
depressed while attempting to start

If these conditions are met, contact SEA-Electric
to arrange diagnostic

•

Vehicle has derated (Become sluggish or accelerating poorly)

Fault diagnosis

Handling methods

The coolant level has dropped

Top up cooling system (Refer to section 9)

The radiator fans are not running

Check Low voltage fuse (as per diagram FB01).
If fine, check connectors are ok.

The Cooling pump is not running

Check Relay is in correctly (as per diagram FB02)
If fine, check connectors are ok.

•

Poor braking performance

Fault diagnosis

Handling methods

Vacuum pump failure
(For vacuum over hydraulic system only)

Ensure that vacuum pump is running when
ignition is turned on
Check fuse in FB01

Brake fluid level has dropped
(For vacuum over hydraulic system only)

Top up brake fluid level.
If OK, Contact SEA-Electric for diagnostic

Air compressor failure
(For air brake system only)

Ensure that air filter on compressor is not blocked
If OK, Contact SEA-Electric for diagnostic

•

Brake deviation

Fault diagnosis

Handling methods

Tyre pressures are not uniform.

Adjust to specified pressure.

Tyre tread wear is uneven

Wheel alignment and tyre replacement required

Unbalanced load

Average the load.

The clearance between the brake drum and the
brake shoes uneven.

Refer to OEM for adjustment

Summary of Contents for ISUZU FSR

























































Search results

Summary of Contents for ISUZU FSR

Reviews:

Related manuals for ISUZU FSR

Brands by name

Popular brands

SEA ISUZU FSR, Owner'S Manual

Search results

Summary of Contents for ISUZU FSR

Reviews:

Related manuals for ISUZU FSR

Brands by name

Popular brands