manualshive.com logo in svg

Sea-doo 2004 GTI, Operator'S Manual, Page: 50 / 130

Share
Download
Sea-doo 2004 GTI Operator'S Manual Download Page 50

49

36) Fuses

All Models except XP DI

Fuses are located under seat in bilge.
Refer to MAINTENANCE for more de-
tails.

XP DI Models

Fuses are located in engine compart-
ment. Refer to MAINTENANCE for
more details.

37) Battery

All Models except XP DI

Battery is located inside engine com-
partment. Refer to SPECIAL PROCE-
DURES.

XP DI Models

Battery is located in bilge under seat.
Refer to SPECIAL PROCEDURES.

38) Side Vanes

(if so equipped)

Side vanes are part of Off-Power Assist-
ed Steering (O.P.A.S.) system. 

The side vanes assist the steering sys-
tem.

All Models with Side Vanes

XP DI Models

39) Rear Access Cover

It gives access to the battery, drive
system, suspension, exhaust system
and bailer pick-ups. Always relatch
cover.

40) Automatic Bilge Pump

Bilge pump evacuates water from the
bilge.

When safety lanyard cap is installed on
its post, bilge pump automatically
turns on. It will remain on until all water
is evacuated, if any, then it will shut
down automatically.

When engine is running, bilge pump
will automatically start periodically to
evacuate water.

WARNING

Check handlebar and correspond-
ing side vanes operation before
starting. Never use side vanes as a
supporting point to board the wa-
tercraft or to lift it. Never turn han-
dlebar while someone is nearby
rear of watercraft. Keep away from
steering moving parts (nozzle,
side vanes, linkage etc.).

smo2004-002a.book  Page 49  Thursday, August 21, 2003  2:54 PM

www.SeaDooManuals.net

Summary of Contents for 2004 GTI



































































































































Reviews:

No comments