background image

18

it is 

ForbiDDEn 

to oPEratE this FirEbox With thE Door oPEn.

swing door: do not open the door too fast as this will create a suction of smoke inside the room. it is 

recommended that you open the damper prior to opening the door.

double sided firebox: never leave both doors open at the same time.

atmospheriC Conditions

Misty or foggy weather may possibly favour back-flow of the smoke, which may be a health hazard. In 

this case only use the fireplace as is necessary.

for safety reasons, assemblies of appliances and accessories not provided or recommended by axis 

or sculpt fireplaces are not permitted. unsuitable equipment may cause dysfunctions and disorder 

upon use).

directly cUt
3 montHS  
6 montHS  
9 montHS  

75%
48%
37%
36% 

78%
62%
46%
38% 

33%
18%
16%
15% 

35%
27%
24%
24% 

1 year
1 1/2 year
2 yearS
2 1/2 yearS

C

C

l

l

C: chunks l: logs

reCommended fuel

This fireplace is designed for only wood fuel. Any fuel other than wood is strictly forbidden. 

As a general rule it is recommended; use dry, well-seasoned HARD WOOD with a 15% moisture content 

in order for the unit to burn effectively and avoid any tarring. the heating output of wood depends on the 

moisture percentage.

5. 

operation & maintenance

Summary of Contents for AXIS 1000



























Reviews: