Scout MT-700 ENT Operation Manual Download Page 39

Page: 39 / 155

МТ-700 fleet tracking system

1 – Configurator
2 – USB-cable
3 ,4 – tie-in connector

Figure 31. Terminal – 485 configurator

adapter

Figure 32. Tie in adapter

Figure 33. 485 Configurator

1 –Configurator
2 – USB cable jack
3 –MT-700 adapter jack

Figure 34. MT-700 – Universal 485

Configurator adapter

Figure 35. USB-cable

Figure 36. Universal 485 configurator

Both autonomous and tie-in connection for configuration are allowed.

The “MT Power Supply” or any other power supply 12-24 VDC can be used to supply

the terminal in the autonomous connection.

If the external power supply is absent, then the terminal configuration can only be

done with a charged backup battery and if plugged in.

The correlation between the terminal connector and the cable jack is shown in the

appendix.

Summary of Contents for MT-700 ENT




























































































































































Search results

Summary of Contents for MT-700 ENT

Reviews:

Related manuals for MT-700 ENT

Brands by name

Popular brands

Scout MT-700 ENT, Operation Manual

Search results

Summary of Contents for MT-700 ENT

Reviews:

Related manuals for MT-700 ENT

Brands by name

Popular brands