1997-99 Chevrolet Venture
Read pages
3-7 for kit
1997-99 Oldsmobile Silhouette
assembly.
1997-99 Pontiac Trans Sport
Radio Removal:
1. Open ashtray and extract one from lower right side of dash bezel.
2. Open 12V socket cover and extract one from lower left dash bezel.
3. Lift bottom of dash
"B1" BRACKET USE HOLE #2
"A1" BRACKET USE HOLE #2
"B1" SOPORTE USA
bezel out to allow
"A1" SOPORTE USA
ABERTURA NO. 2
ABERTURA NO. 2
top edge to unhook
from under air
vents, unplug
lighter, switches
and remove dash.
4. Extract two 7mm
hex head screws
holding radio in,
unplug connectors
LEFT SIDE
and remove radio.
RIGHT SIDE
LADO IZQUIERDA
FRONT OF KIT
LADO DERECHO
FRENTE DE ESTUCHE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1992-95 Oldsmobile Achieva
3-7 for kit
assembly.
Radio Removal:
1. Extract the two screws from the bottom of the dash bezel, below the radio and above the console pocket,
securing it to the dash.
2. Extract the two screws above the instrument cluster.
CARRIAGE BOLT
3. Remove the two screws above the AC vent located in the
PERNO DE PORTE
center of the dash.
4.
Pull the dash bezel out away from the dash and using a
panel removal tool/screwdriver, carefully disconnect the
fastening clips securing the dash vents (the one in the
BOTTOM
FONDO
center and the one on the driver's side) to the bezel.
5. Disconnect all the connectors and slide the dash bezel
away from the dash towards the passenger side.
6. Extract the two 10mm bolts securing the radio to the
FLANGE NUT
dash, pull the radio from the cavity, unplug all the
TUERCO REBORDE
connectors, and remove the radio.
SECURE THE KIT PANEL TO THE DASH USING THE SUPPLIED CARRIAGE BOLTS AND NUTS.
Asegure el panel estuche al tablero usando los pernos de porte y tuercos proveidos.
Read pages
1985-91 Oldsmobile Cutlass Calais
3-7 for kit
assembly.
Radio Removal:
BREAK OFF TAB
1. Open armrest and extract (2) Phillips
ROMPE LA LENGUETA
head screws from bottom of pocket.
2. Remove pocket and extract (2) 10mm
bolts from underneath. Lift and slide
armrest towards rear of car.
BOTTOM
3. Extract (2) 7mm/t-15 bolts from rear edge
FONDO
of gear select lever trim panel. Remove
ashtray (on center console) and extract
(1) 7mm/t-15 bolt from underneath.
4.
Put car in low gear. Lift and slide center
console towards rear of car
"C1" BRACKET
USE HOLE #5
5. Gently unsnap and remove radio trim
bezel.
"C1" SOPORTE
6. Extract (2) 7mm/T-15 Torx screws
USA ABERTURA NO. 5
securing radio to the dash, unplug wiring,
antenna, and remove radio.
"D1" BRACKET USE HOLE #1
"D1" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
24
Read pages
1993-02 Pontiac Firebird
3-7 for kit
Radio Removal:
assembly.
1. Using a panel removal tool/screwdriver, carefully release the fastening clips from around the perimeter of
the radio trim bezel and remove the bezel.
2. Extract the four screws securing the radio to the dash, pull the radio from the cavity, unplug all the
connectors, and remove the radio.
"B1" BRACKET USE HOLE #1
"A1" BRACKET USE HOLE #1
"B1" SOPORTE
LEFT SIDE
RIGHT SIDE
LADO IZQUIERDA
LADO DERECHO
"A1" SOPORTE
USA ABERTURA NO. 1
USA ABERTURA NO. 1
1
1
1
FRONT OF KIT
1
"C2" BRACKET
"B2" BRACKET
FRENTE DE ESTUCHE
USE HOLE #1
USE HOLE #1
"C2" SOPORTE USA ABERTURA NO. 1
"B2" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1985-92 Pontiac Firebird
3-7 for kit
assembly.
Radio Removal:
1. Carefully pull on the edges of the radio trim panel to release the panel clips and remove the panel.
2. Remove the four screws which secure the radio to the console.
3. Disconnect the antenna, speaker leads and all the electrical connections, then remove the radio.
LEFT
RIGHT
"A1" BRACKET USE HOLE #1
LADO IZQUIERDA
LADO DERECHO
"B1" BRACKET USE HOLE #1
"B1" SOPORTE
"A1" SOPORTE
USA ABERTURA NO. 1
USA ABERTURA NO. 1
1
1
TRIM BRACKET
CORTA EL
SOPORTE
FRONT OF KIT
"C2" BRACKET
1
1
USE HOLE #1
FRENTE DE
"C2" SOPORTE
ESTUCHE
"D2" BRACKET USE HOLE #1
USA ABERTURA NO. 1
"D2" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1996-98 Pontiac Grand Am
3-7 for kit
assembly.
Radio Removal:
1. Extract two screws from the dash bezel above instrument/gauges.
2. Extract two screws from back of deep storage pocket below the radio.
3. Carefully pull out on the instrument/radio panel to release snap clips, unplug switches and remove bezel.
4. Extract three 7mm screws securing radio, unplug connectors, antenna lead, and remove radio.
LEFT SIDE
RIGHT SIDE
"B1" BRACKET USE HOLE #1
LADO IZQUIERDA
LADO DERECHO
"B1" SOPORTE USA
ABERTURA NO. 1
"C2" BRACKET
USE HOLE #5
1
"C2" SOPORTE
USA ABERTURA NO. 5
FRONT OF KIT
2
FRENTE DE
TRIM BRACKET
ESTUCHE
CORTA EL SOPORTE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
29
