Schweitzer Engineering SEL-2032 Instruction Manual Download Page 86 | Manualshive

Page: 86 / 354

Schweitzer Engineering SEL-2032 Instruction Manual Download Page 86

3.16

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Job Done Examples

Example 3: Collect SEL Relay Status and Measurements

*>>

MAP 2 <Enter>

Port 2 Database Assignments

Region Data Type # Records

GLOBAL --
LOCAL --
BUF --
D1 B METER
D2 B TARGET
D3 Unused
D4 Unused
D5 Unused
D6 Unused
D7 Unused
D8 Unused
A1 Unused
A2 Unused
A3 Unused
USER Unused

*>>

Figure 3.14

MAP Command Example

c. Verify the various metering quantities that are being

collected and stored in the SEL-2032 by issuing the
command

MAP 2:METER

or

MAP 2:D1

, as shown in

The SEL-2032 responds with a map of the specific
region, including a listing of the data item names, the
starting address for each data item, and the type of data
stored at each address.

*>>

MAP 2:METER

Port 2, Data Region METER Map

Data Item Starting Address Type

_YEAR 2000h    int
DAY_OF_YEAR 2001h    int
TIME(ms) 2002h    int[2]
MONTH 2004h    char
DATE 2005h    char
YEAR 2006h    char
HOUR 2007h    char
MIN 2008h    char
SECONDS 2009h    char
MSEC 200Ah    int
IA 200Bh    float[2]
IB 200Fh    float[2]
IC 2013h    float[2]
IN 2017h    float[2]
VA 201Bh    float[2]
VB 201Fh    float[2]
VC 2023h    float[2]
VS 2027h    float[2]
FREQ 202Bh    float[2]
VBAT 202Fh    float[2]
IAB(A) 2033h    float[2]
IBC(A) 2037h    float[2]
ICA(A) 203Bh    float[2]
VAB(V) 203Fh    float[2]
VBC(V) 2043h    float[2]
VCA(V) 2047h    float[2]
PA(MW) 204Bh    float
QA(MVAR) 204Dh    float
PB(MW) 204Fh    float
QB(MVAR) 2051h    float
PC(MW) 2053h    float
QC(MVAR) 2055h    float
P(MW) 2057h    float
Q(MVAR) 2059h    float
I0(A) 205Bh    float[2]
I1(A) 205Fh    float[2]
I2(A) 2063h    float[2]

Courtesy of NationalSwitchgear.com

«
...
84
85
86
87
88
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments