Schweitzer Engineering SEL-2032 Instruction Manual Download Page 53 | Manualshive

Page: 53 / 354

background image

2.7

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Installation

Mounting and Connections

NOTE

: Never use standard null-

modem cables with the SEL-2032.
Using any non-SEL cable can cause
severe power and ground problems
involving pins 1, 4, and 6 on the
SEL-2032 communication ports.

Please call the SEL factory if you have any questions about cables and cable
connections.

The following list provides additional rules and practices you should follow
for successful communication using EIA-232 serial communication devices
and cables:

➤

You should keep the length of the communication cables as
short as possible to minimize communication circuit
interference and also to minimize the magnitude of hazardous
ground potential differences that can develop during abnormal
power system conditions.

➤

EIA-232 communication cable lengths should never exceed 50
feet, and you should always use shielded cables for
communication circuit lengths greater than 10 feet.

➤

Modems are required for communication over long distances
and to provide isolation from ground potential differences
between device locations.

➤

Route communication cables well away from power and
control circuits. Switching spikes and surges in power and
control circuits can cause noise in the communications circuits
if not adequately separated.

➤

Lower baud rate communication is less susceptible to
interference and will transmit greater distances over the same
medium than with higher baud rates. You should use the lowest
baud rate that provides adequate data transfer speed.

Network
Connections

See your plug-in protocol card instruction manual to determine appropriate
network connection methods.

Cable Pinout
Configuration

shows the cable pinout configuration for cables that connect the

SEL-2032 to a local PC for configuration. Use this cable type with a terminal
emulation program or the SEL-5020 Settings Assistant software.

C272A

9-pin DTE devices
without IRIG

DB-9P

DTE

no

no

C273A

9-pin DTE devices
w/ IRIG: SEL-500
series, SEL-300
series except
SEL-321

DB-9P

DTE/

IRIG-B

yes

yes

Table 2.4

Communication Cables for Devices Attached to SEL-2032

(Sheet 2 of 2)

SEL

Cable #

Connect

SEL-2032 to:

Remote

Connector

(on cable)

Port Type

RTS/CTS

Supported

IRIG-B

Included

Courtesy of NationalSwitchgear.com

«
...
51
52
53
54
55
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: Omnia Pages: 102

Brand: Garland Pages: 4

Brand: Falcon Pages: 24

Brand: Gate Pages: 8

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Brand: Renesas Pages: 4

Brand: AMX Pages: 1

Brand: EZCast Pages: 24

Brand: Echo Pages: 21

Lexicon MPX 200

Brand: Harman Pages: 77

Brand: Nexus Pages: 9

Brand: C&H Technologies Pages: 2

Brand: Vxl Pages: 4

Brand: Juniper Pages: 30

Brand: LevelOne Pages: 10

Brand: SET Pages: 38

EK-FC 780 GTX Lightning

Brand: ekwb Pages: 3

Brand: Alphacool Pages: 3

Brand: C-Data Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands