Schweitzer Engineering SEL-2032 Instruction Manual Download Page 316 | Manualshive

Page: 316 / 354

background image

10.6

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Testing and Troubleshooting

Relay Firmware Upgrades

CAUTION:

Equipment

components are sensitive to

electrostatic discharge (ESD).
Undetectable permanent damage
can result if you do not use proper
ESD procedures. Ground yourself,
your work surface, and this
equipment before removing any
cover from this equipment. If your
facility is not equipped to work with
these components, contact SEL
about returning this device and
related SEL equipment for service.

!

Step 4. Locate the battery on the front left-hand side of the main board.

Step 5. Remove the battery from beneath the clip and install a new one;

the positive side (+) of the battery faces up.

Step 6. Replace the front panel and front-panel screws and tighten

securely.

Step 7. Replace any cables removed from the SEL-2032.

Step 8. Apply power to the SEL-2032, and set the date and time again.

A battery failure will be reported the first time you power-up
with a new battery because the date and time reported by the
battery-backed clock will not be valid.

The SEL-2032 monitors the clock registers on power-up. If the clock registers
are invalid, the battery is presumed to be discharged and a battery failure is
reported.

Relay Firmware Upgrades

When you upgrade the firmware for an SEL relay attached to the SEL-2032,
perform the following steps:

Step 1. Take the relay out of service.

The SEL-2032 will show the relay’s port status as Inactive and
will no longer collect data.

Step 2. Upgrade the relay firmware according to its upgrade

instructions.

Step 3. Apply power to the relay and reset its settings, as necessary.

Step 4. Perform any relay testing that your practices require.

Step 5. Reconnect the relay to the SEL-2032, if necessary.

Step 6. Connect a computer terminal to the SEL-2032 and go to Access

Level 2.

Step 7. Make a backup copy of your SEL-2032 settings before

continuing with the next steps.

The backup settings may be needed if the SEL-2032 has auto
configuration problems with the upgraded relay causing
settings to be lost.

Step 8. Execute a

SET P

command on the relay’s port and auto-

configure the port; save these settings.

Step 9. Confirm that the SEL-2032 is now communicating as before.

Place the relay back in service.

Courtesy of NationalSwitchgear.com

«
...
314
315
316
317
318
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Enterprise Filter Authentication R3000

Brand: 8e6 Technologies Pages: 66

Brand: Delta Tau Pages: 74

iW-RainboW-G30D

Brand: iWave Pages: 89

Brand: IOtech Pages: 16

OMB-DAQBOARD-3000 Series

Brand: Omega Pages: 108

Brand: Altera Pages: 93

NetVanta 6355 PoE

Brand: ADTRAN Pages: 46

Brand: Campbell Pages: 38

Optane Persistent Memory 200 Series

Brand: Supermicro Pages: 54

Brand: Renesas Pages: 4

iCE40 SPRAM Series

Brand: Lattice Semiconductor Pages: 12

Brand: mikroElektronika Pages: 2

HHM Series HHM2409

Brand: TDK Pages: 2

Slideaway CL1008

Brand: ATEN Pages: 77

Brand: DayTronic Pages: 13

PCI-AD-x16HE-BG4

Brand: Serial Cables Pages: 18

Dablet DVP 5000

Brand: DarbeeVision Pages: 10

HYPER-BT-E38 1 Series

Brand: IEI Technology Pages: 95

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands