manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

1.15

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Introduction and Specifications

Functions

Use SEL

OGIC

 control equations to control when the SEL-2032 sends 

messages. You can use data from other IEDs, periodic and time of day 
functions, commands from protocol masters, and calculated data within the 
SEL-2032 as arguments in SEL

OGIC

 control equations. When the result of the 

SEL

OGIC

 control equation transitions from logical 0 to logical 1 (a rising 

edge), the SEL-2032 sends the message.

SEL Interleaved Protocols

The SEL-2032 simplifies substation network design and construction by 
interleaving several conversations on one cable between the relay and the 
SEL-2032. First, the SEL-2032 uses Fast Meter, Fast Operate, and Fast SER 
(Fast Message Protocol) for data collection and control. Second, you can use a 
transparent connection from one of the SEL-2032 ports for ASCII 
communications with the relay for configuration, diagnostics, and report 
collection. Third, the SEL-2032 generates an IRIG-B signal on each port for 
time synchronization.

Because all three conversations are interleaved, it is often unnecessary to 
connect more than one communications cable to the relay to accomplish 
engineering connections, data collection, and time synchronization. If you use 
an SEL-2810 Fiber-Optic Transceiver, all three conversations occur over a 
single fiber pair.

Auto-Configuration

Setting the SEL-2032 communication parameters for a port is simplified 
through the auto-configuration process of the SEL-2032. This process 
determines the proper data communication rate to communicate with the 
connected device. The SEL-2032 also determines the startup string, relay 
type, Fast Meter capability, and relay ID for any SEL relay connected to its 
port. You should use the 

SET P

 command to activate and configure each port 

that has a connected device.

When you connect the SEL-2032 to an SEL relay, you do not have to 
configure the individual messages, parsing, and control activation messages. 
The SEL-2032 connects to the relay and collects configuration data through a 
process called auto-configuration. When you connect the cable and configure 
the port for an SEL device, you will be prompted to start auto-configuration.

Once auto-configuration is complete, you can enable control messages from 
the SEL-2032 to the relay, configure the relay to accept control messages, and 
trigger them automatically through SEL

OGIC

 control equations. Whenever a 

remote bit or breaker bit changes state, the SEL-2032 automatically sends a 
control message to the relay. You do not have to configure or write the 
outgoing message.

“20” Messages

When you connect to an SEL relay and have completed auto-configuration, 
you can collect data from the relay using “20” messages. The SEL-2032 
automatically creates request messages, parses the incoming data, and labels 
the data in the SEL-2032 database. The most frequently used “20” messages 
are 20METER and 20TARGET. The 20METER message collects metering 
and measurement data, while the 20TARGET message collects binary status 
data from inputs, outputs, and relay protection elements.

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Baicells Nova430i Quick Manual preview
Nova430i
Brand: Baicells Pages: 8
Udoo NEO Step-By-Step Manual preview
NEO
Brand: Udoo Pages: 7
A10 Thunder Series Manual preview
Thunder Series
Brand: A10 Pages: 52
ETAS FETK-S2.1 User Manual preview
FETK-S2.1
Brand: ETAS Pages: 69
SIIG ID-P20211-S1 Quick Installation Manual preview
ID-P20211-S1
Brand: SIIG Pages: 20
Delta Electronics Through Hole Power Inductors 1411 Product Specifications preview
Through Hole Power Inductors 1411
Brand: Delta Electronics Pages: 1
Hauppauge WinTV USB Installation And Reference Manual preview
WinTV USB
Brand: Hauppauge Pages: 55
ZALMAN RESERATOR2 Installation And Operational Manual preview
RESERATOR2
Brand: ZALMAN Pages: 18
Procool SP480 Series Instructions preview
SP480 Series
Brand: Procool Pages: 2
Echelon i.LON SmartServer Hardware Manual preview
i.LON SmartServer
Brand: Echelon Pages: 34
Alphacool EISBAER PRO Quick Start Manual preview
EISBAER PRO
Brand: Alphacool Pages: 9
Supermicro BPN-SAS3-LB16A-N10 User Manual preview
BPN-SAS3-LB16A-N10
Brand: Supermicro Pages: 11
National Instruments PXI-GPIB Getting Started preview
PXI-GPIB
Brand: National Instruments Pages: 45
Inter-m S- Media Manual preview
S- Media
Brand: Inter-m Pages: 20
ST L6470H Manual preview
L6470H
Brand: ST Pages: 64
Dataprobe iBoot-PDU4-C10 User Manual preview
iBoot-PDU4-C10
Brand: Dataprobe Pages: 72
TRENDnet TEG-S3M8S15 Specifications preview
TEG-S3M8S15
Brand: TRENDnet Pages: 2
IBM 55PUS8118 SCSI-2 Installation Manual preview
55PUS8118 SCSI-2
Brand: IBM Pages: 42

Brands by name

Popular brands

Load more brands