Schweitzer Engineering SEL-2032 Instruction Manual Download Page 121 | Manualshive

Page: 121 / 354

background image

5.7

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Message Strings

20EVENT Features

20EVENT Features

Because SEL relays may trigger multiple event reports in rapid succession, the
SEL-2032 has special features based on these triggers to facilitate collecting
event reports. To take advantage of these special features, you must set

20EVENT

as a user-defined command with

SET U

. The SEL-2032 then

keeps track of the number of summary event reports received from the SEL
relay on that port. You must then set MESG3 or MESG3A to 20EVENT,
20EVENTS, or 20EVENTL. The SEL-2032 will then collect the oldest
unread event report from the SEL relay. The CMD

x

bit corresponding to the

20EVENT

command continues to retrigger every 5 minutes as long as there

are uncollected event reports. (To have the CMD

x

bit trigger immediately on

Table 5.4

Predefined Strings for Auto-Messages with Auto-Configured SEL IEDs

String

Comment

20METER

Send ASCII meter or Fast Meter command, as appropriate.

20DEMAND

Send ASCII demand meter or
fast demand meter command, as appropriate.

20TARGET

Send ASCII target command sequence or Fast Meter, as appropriate.

a

a

When the SEL-2032 collects target data from relays that do not have Fast Meter capability,
the

TARGET

commands sent by the SEL-2032 may momentarily modify the front-panel targets

on the relays—just as if you were sending the

TARGET

command to the relay without the

SEL-2032.

20HISTORY

Send ASCII history command.

20STATUS

Send ASCII status command.

20BREAKER

Send ASCII breaker command.

20EVENT

Send ASCII request for standard (4 sample/cycle)
event report. Stored in a parsed format. (Refer to the
following subsection for some additional features.)

20EVENTS

Send ASCII request for standard (4 sample/cycle)
event report. Stored in a literal format. (Refer to the
following subsection for some additional features.)

20EVENTL

Send ASCII request for long (16 sample/cycle)
event report. Stored in a literal format. (Refer to the
following subsection for some additional features.)

Table 5.5

Other Predefined Strings for Auto-Messages

String

Comment

20USER

No message is sent, but data from User Region is copied to this region.

Table 5.6

Predefined Strings for General-Purpose User-Defined Commands

String

Comment

20EVENT

Recognize summary event reports received from SEL relays and
trigger with delay. Will continue to retrigger until all reports are collected.

20EVENTQ

Recognize summary event reports
received from SEL relays and trigger immediately.

20STATUS

Recognize status messages received from SEL relays.

20GROUP

Recognize group switch messages from SEL relays.

Courtesy of NationalSwitchgear.com

«
...
119
120
121
122
123
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

Brand: Yaesu Pages: 2

Brand: Analog Devices Pages: 76

Brand: Gate Pages: 8

Millennium P650

Brand: Matrox Pages: 54

Brand: ZyXEL Communications Pages: 215

Brand: Renesas Pages: 2

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

Brand: Extron electronics Pages: 19

Wireless Outdoor Bridge XI-1500-IH

Brand: IMC Networks Pages: 13

HHM Series HHM1521

Brand: TDK Pages: 2

USB device 622x

Brand: National Instruments Pages: 23

Brand: TP-Link Pages: 2

Brand: Aegis Pages: 7

MS-9A95 WindBOX IV Advanced

Brand: MSI Pages: 51

Brand: InfoStor Pages: 6

Brand: Syris Pages: 27

Mercury TV Card

Brand: Kobian Pages: 30

DEQ-P8000 - DSP - External

Brand: Pioneer Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands