manualshive.com logo in svg

SCHUNK FT-AXIA Series, Assembly And Operating Manual, Page: 38 / 44

Share
Download
SCHUNK FT-AXIA Series Assembly And Operating Manual Download Page 38

EU Declaration of Conformity

38

02.00 | FT-AXIA | Assembly and Operating Manual | en | 1517831

8 EU Declaration of Conformity

Manufacturer/
Distributor

SCHUNK GmbH & Co. KG Clamping and gripping technology 
Bahnhofstr. 106 - 134 
D-74348 Lauffen/Neckar

We hereby declare on our sole authority that the product meets the requirements of the
following directives at the time of the declaration. 
The declaration is rendered invalid if modifications are made to the product.

Product designation:

Force/torque sensor FT-AXIA
This declaration of conformity is valid for all variants mentioned
in the appendix.

•

Electromagnetic compatibility (EMC directive) 2014/30/EU

Applied harmonized standards, especially:

EN 61326-2-3:2013

Electrical equipment for measurement, control and laboratory
use - EMC requirements – Part 2-3: Particular requirements –
Test configuration, operational conditions and performance
criteria for transducers with integrated or remote signal
conditioning. (IEC 61326-2-3:2012)

EN ISO 12100:2010

Safety of machinery - General principles for design -
Risk assessment and risk reduction

All related technical documentation has been prepared in electronic form according to
Directive 2014/30/EU and will be made available to national authorities on demand. The
signatory is resident at the manufacturer's address and is authorized to compile this
documentation.

Signed for and on behalf of: SCHUNK GmbH & Co. KG

Lauffen/Neckar, November 2022

Dr.-Ing. Manuel Baumeister,
Technology & Innovation

Summary of Contents for FT-AXIA Series













































Reviews:

No comments