• 5 •
USING THE LED LIGHT
Choose from Normal, SOS and Emergency Flash modes.
1. Press the button on the side of the unit for 2 seconds to turn on the LED light. The icon will show on the LCD screen.
2. Press the button again for SOS mode.
3. Press the button once more for emergency flashing.
4. Long press the button for 2 seconds to turn off the LED light.
USING THE AC POWER OUTLETS
The SL1466 is equipped with a 500W pure sine wave inverter, which produces power for all electronic devices and appliances.
It is important to know the continuous wattage of the device you plan to use with the AC outlets. The unit must be used with devices drawing 500 watts or less.
Devices such as fans or electric motors require additional power to start (commonly known as the “starting” or “peak” power). The generator can supply a momentary surge
in wattage of as high as 1000W for less than 1/10 of a second; however even devices rated less than the maximum 500 watts can exceed the inverter’s surge capability
and cause an automatic overload shutdown.
Do not use the inverter with a product that draws a higher wattage than the inverter can provide, as this may cause erratic operation.
CAUTION: Always run a test to establish whether the inverter will operate a particular piece of equipment or device.
In the event of a power overload (noted with a flashing Warning icon), the inverter is designed to automatically shut down. This safety feature prevents damaging the
inverter while testing devices and equipment within the 500-watt range.
If powering more than one device, start one device at a time to avoid a power surge and/or inverter overload. The surge load of each device should not exceed the
inverter’s Continuous Operation wattage rate.
You can use an extension cord from the inverter to the device without significantly decreasing the power being generated by the inverter. For best operating results, the
extension cord should be 16 AWG (1.31 mm
2
) or larger and no longer than 50 feet.
WARNING! RISK OF ELECTRIC SHOCK.
Incorrect operation of your inverter may result in damage and personal injury. The inverter output is 110V AC and can shock or electrocute the same as any ordinary
household AC wall outlet.
NOTE: The maximum continuous load is 500 watts. Do not use the AC outlets with a product that draws more than 500 watts, as this may cause erratic operation.
CAUTION:
• Do not connect an AC power source to the 110V AC outlets.
• Do not connect the unit’s AC power cord to its 110V AC outlets.
NOTE: Do not power an AC device while charging the internal battery.
1. Connect your AC-powered devices or small household appliances to one or more of the unit’s two AC outlets.
NOTE: Make sure the device to be powered is OFF before inserting the plug into the AC power outlet.
2. Press the AC Power button. The AC Output icon will show on the display, to confirm that the unit is on and ready to provide AC power. The Power Output indicator
will also show on the display.
NOTE: Extended operation of an AC device may result in excessive battery drain.
3. Recharge the unit when the battery level is below 40%.
ESTIMATED RUN-TIMES
APPLIANCE TYPE
ESTIMATED RUN TIME
CHARGES
Jig Saw
2.4 hours
—
Projector
7 hours
—
12V Heated blanket
13 hours
—
12V Cooler
15 hours
—
Mini Fridge
20 hours
—
Television
21 hours
—
Drone
22 hours
103
Fan
26 hours
—
Router
54 hours
—
Table lamp
59 hours
—
Laptop
106 hours
12
LED lights
150 hours
—
Camera
190 hours
99
Radio
222 hours
—
Tablet
247 hours
15
Speaker
680 hours
44
Smartphone
765 hours
49
NOTE: Actual time may vary. Times are based on the internal battery being fully charged.
7. MAINTENANCE AND CARE
• Recharge the unit when the battery level is below 40%.
• Never completely discharge the internal battery.