manualshive.com logo in svg

Schulte FX-520, Operator'S Manual

Share
Download
Schulte FX-520 Operator'S Manual Download Page 51

ASSEMBLY

FX-520   06/16

Assembly Section 3-5

© 2016 Alamo Group Inc.

ASSEMBL

Y

Driveline Shield Chains

Attach CV shield chain to tractor or cutter hitch
allowing sufficient slack for turning.

IMPORTANT:

 OSHA, ASABE and SAE standards

require that all rotating shafts be guarded against
contact. The unchained plastic shields can rotate
with the driveline, but must stop when they contact
another object.

Note: 

Driveline shields may also be chained to the

gearbox cone using the supplied chains.

The shields 

must

 be regularly greased and

checked that they rotate freely on the driveline.
Refer to the Lubrication Section for greasing
intervals.

Precision Clevis - C000-360

Adjust the opening of the precision clevis by
shimming the wear plate with the spacers. Remove
the two 5/8” bolts and lockwashers and stack the
spacers between the wear plate and the hitch block
until the opening measures less than 1/8” taller than
the drawbar. Replace unused spacers under the
hitch block and reinstall the lockwashers and bolts.

NEVER USE YOUR HANDS TO STEADY THE HITCH BLOCK WHILE THE TRACTOR IS
BEING BACKED INTO THE HITCH.

NEVER STAND BETWEEN THE TRACTOR AND THE ROTARY CUTTER WHILE THE
TRACTOR IS BEING BACKED INTO THE HITCH.

Summary of Contents for FX-520







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands