manualshive.com logo in svg

Schulte FX-520, Operator'S Manual

Share
Download
Schulte FX-520 Operator'S Manual Download Page 48

ASSEMBLY

FX-520   06/16

Assembly Section 3-2

© 2016 Alamo Group Inc.

ASSEMBL

Y

GENERAL INFORMATION

The FX-520 Mower can only be used with tractors that have 1000 RPM PTO.

Check oil level in all gearboxes before operation. Refer to the Lubrication section of this
manual for recommended oil type and viscosity.

Lubricate all grease fittings. Refer to the grease schedule in this manual.

Check that all nuts and bolts are in place and are properly tightened. Refer to the Maintenance section of this
manual for required bolt grades and torques.

If chain guards are not already assembled to the machine, refer to the parts manual for details of their general
arrangement and the fasteners to install them.

Check that all tires are inflated to proper specifications. Refer to Maintenance section of this manual for
required tire pressures.

HYDRAULIC CIRCUITS

Wing System

If the rotary cutter has been supplied to you already assembled it is possible that the wing lift
hydraulic cylinders are not completely filled with oil. An indication of this will be that the wing
lift lock up pins cannot be removed freely. 

The wing lift system is marked in blue at the tractor connection.

First fully retract the hydraulic wing lift cylinders then remove the wing lock up pins.

NEVER FORCE THE WING LIFT LOCK PINS OUT OF THEIR LOCK POSITION AS THE
WINGS MAY SUDDENLY DROP CAUSING INJURY OR DEATH.

Summary of Contents for FX-520







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands