schmersal SLC440COM Series Operating Instructions Manual Download Page 11

11

SLC440COM Series

SLG440COM Series

Operating instructions

Safety light curtain / safety light grid

EN

4.9  Accessories, included in delivery

Mounting kit MS-1100

The mounting kit consists of 4 pcs steel angles and 8 pcs fixing 

screws (Type Torx plus 10IP)

5,5

17

28

24

7

11

24

38

MSD5 spacer

The kit consists of 2 pcs spacers Available as of a protection zone 

height of 1050 mm Mounting must be used in case of vibrations 

M4

10

8

33

7,7

4.10 Optional accessory

Centre support MS-1110

Mounting kit consists of 2 pcs steel angles and 4 pcs spacers for 

central fixing

4

27,8

11,5

19,5

11,5

54,3

69

38

5,5

3

27

3

7

 

 

Connecting cable for emitter / receiver (4-pole)

Article No. Designation (description)

Length

101207741 KA-0804 (female connector M12, 4-pole)

5 m

101207742 KA-0805 (female connector M12, 4-pole)

10 m

101207743 KA-0808 (female connector M12, 4-pole)

20 m

Connecting cable for receiver (5-pole)*

Article No. Designation (description)

Length

103010816 A-K5P-M12-S-G-5M-BK-2-X-A-4-69 

(Female connector M12, 5-pole)

5 m

103010818 A-K5P-M12-S-G-10M-BK-2-X-A-4-69 

(Female connector M12, 5-pole)

10 m

103010820 A-K5P-M12-S-G-15M-BK-2-X-A-4-69 

(Female connector M12, 5-pole)

15 m

* For use in the operating mode Restart Interlock (manual reset)

Adapter cable for alignment kit:

Article No. Designation (description)

Length

103034548 KA-0827 (cable for alignment mode 

M12 coupling (female/male connector), 4-pole)

03 m

Adapter cable for parameter setting

Article No. Designation (description)

Length

103016100 KA-0896 (pushbutton with command device)

25 m

Test rod PLS

The test rod is used for testing the protection field

MSD4 Vibration damper

Kit consists of: 8 pcs vibration dampers 15 x 20 mm, 8 pcs M5 cylinder 

head screws with hexagon socket, 8 pcs spring washers Mounting 

using MS-1100

The MSD4 vibration damper kit is recommend to be used for damping 

vibrations and oscillations on the AOPD For applications with higher 

mechanical stresses, eg presses, punching machines, we recommend 

the MSD4 kit In this way, the availability of the AOPD is increased

Summary of Contents for SLC440COM Series

















Reviews: