3
SLC440 Series
SLG440 Series
Operating instructions
Safety light curtain / safety light grid
EN
2.6 Technical data
Standards:
EN 61496-1, EN 61496-2,
ISO 13849, EN 62061
Material of the enclosure:
Aluminium
Protection field heights:
- SLC440
170 mm - 1930 mm
- SLG440
500 mm, 800 mm, 900 mm
Detection ability for test bodies:
- SLC440
14 mm and 30 mm
- SLG440
2 beams with resolution 500 mm
3)
3 beams with resolution 400 mm
3)
4 beams with resolution 300 mm
3)
Range of the protection field:
SLC440
- resolution 14 mm
03 … 7 m
- resolution 30 mm
03 … 10 m
SLG440
- standard
03 … 12 m
- high range
30 … 20 m
Response time:
- beam coding (normal)
1 - 48 beams = 10 ms
49 - 144 beams = 20 ms
145 - 192 beams = 28 ms
- beam coding A
1 - 48 beams = 15 ms
49 - 144 beams = 27 ms
145 - 192 beams = 40 ms
Rated operating voltage:
24 VDC ±10% (PELV) supply unit
I
max
2.0 A, to EN 60204 (power drop ≤ 20 ms)
Rated operating current:
- Emitter:
max 200 mA
- Receiver:
max 700 mA
Wavelength of the infrared radiation:
880 nm
Emitter, infrared emitted radiation
- to DIN EN 12198-1:
Category 0
- to DIN EN 62471:
free group
Safety outputs
OSSD1, OSSD2:
2 x short-circuit proof PNP semi-conductor outputs
Test impulse cycle OSSD:
750 ms
Test impulse length:
100 µs
Switching voltage HIGH¹
)
:
15 … 264 V
Switching voltage LOW¹
)
:
0 … 2 V
Switching current each OSSD:
0 … 250 mA
Leakage current²
)
:
1 mA
Load capacity:
0 … 22 µF
Load inductance
4)
:
0 … 2 H
Admissible conduction resistance between OSSD and load:
2.5 Ω
Admissible conduction resistance of the supply cable:
1.5 Ω
Contactor control (EDM)
Input voltage HIGH (inactive):
11 … 30 V
Input voltage LOW (active):
0 … 20 V
Input current HIGH:
3 … 10 mA
Input current LOW:
0 … 2 mA
Input release restart interlock/restart interlock 2
Input voltage HIGH (active):
11 … 30 V
Input voltage LOW (inactive):
0 … 20 V
Input current HIGH:
3 … 10 mA
Input current LOW:
0 … 3 mA
Functions:
automatic mode, restart interlock,
double reset, contactor control,
beam blanking fixed and floating,
beam coding A
Signal times
Contactor control:
max 500 ms
Restart interlock (manual reset):
50 ms … 15 s, signal
transmission in case of falling edge
LED indications emitter:
emitting, status
LED indications receiver:
OSSD ON, OSSD OFF, restart, signal
reception, blanking, information, Bluetooth
Connection:
M12 connector plug with metal thread, receiver 8-pole,
transmitter 4-pole
Ambient temperature:
−25° C … + 50° C;
at −25° C: Reduction of range by −10%
Storage temperature:
−25° C … + 70° C
Interface:
Diagnostics and function setting
Protection class:
IP67 (IEC 60529)
Resistance to vibration:
10 … 55 Hz to IEC 60068-2-6
Resistance to shock:
10 g, 16 ms, to IEC 60028-2-29
Version:
as of 2020 version 30
¹
)
According to IEC 61131-2
²
)
In case of failure, the leakage current at the most flows to the OSSD
cable The downstream control element must recognise this state as
LOW A safety PLC must detect this state
³
)
Resolution = beam di beam diameter 10 mm
4)
The load induction generates an induced voltage during the switch-
off, which compromises the downstream components (spark
quenching element)
This device complies with Industry Canada's license exempt RSSs
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including
interference that may cause undesired operation of the device
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence L'exploitation est
autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage;
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement
