schmersal SEP 01.0 Operating Instructions Manual Download Page 4

Page: 4 / 38

Operating instructions

Two-hand control panel

SEPK 02.0 / SEPG 05.3 / SEP 01.0 /

SEP 01.4 / SEPLC 05.2 / SEP 07.0 / SEP 09.0

Switching interlock = yellow latching pushbutton

in addition to the red emergency stop command

device (incl. label "switching interlock"), 2 NO +

2 NC

Ergonomic pushbutton (with spring in the device

head) ADP55/3SW, actuating force 10.5 N, 1 NC

+ 1 NO

Ergonomic pushbutton (without spring in the

device head) ADP55/3SW o.F., actuating force

7.0 N, 1 NC + 1 NO

Not all component variants, which are possible according to this order

code, are available.

SEPLC 05.2.

➀

➁

➂

➃

➄

No. Option

Description

➀

Diameter of the command device heads (Elan)

Diameter of the command device heads

(Elan or Elan + Siemens)

Diameter of the command device heads

(Elan or Siemens)

Diameter of the command device heads (Elan)

no command device mounted (empty enclosure

with 3 × mounting hole Ø 22.3 mm)

Special version (with the following special orde-

ring code)

➁

Command devices Elan

Command devices Siemens

➂

Mounting hole 22.3 mm

Mounting hole 30.5 mm

➃

NC and NO contact of the mushroom-shaped

pushbutton in separated form

➄

Emergency stop command device 2 NO + 2 NC

Switching interlock = yellow latching pushbutton

instead of the red emergency stop command

device (incl. label "switching interlock"),

1 NO + 1 NC

Switching interlock = yellow latching pushbutton

instead of the red emergency stop command

device (incl. label "switching interlock"),

2 NO + 2 NC

Switching interlock = yellow latching pushbutton

in addition to the red emergency stop command

device (incl. label "switching interlock"),

1 NO + 1 NC

Switching interlock = yellow latching pushbutton

in addition to the red emergency stop command

device (incl. label "switching interlock"),

2 NO + 2 NC

Ergonomic pushbutton (with spring in the device

head) ADP55/3SW, actuating force 10.5 N,

1 NC + 1 NO

Ergonomic pushbutton (without spring in the

device head) ADP55/3SW o.F., actuating force

7.0 N, 1 NC + 1 NO

Prepunched, removable Al panel with a total of

11 mounting holes Ø 22.3 mm

Prepunched, removable Al panel with a total of

11 mounting holes Ø 22.3 mm, additional moun-

ting holes sealed with round blanking plugs

Not all component variants, which are possible according to this order

code, are available.

SEP 09.0.

➀

➁

➂

➃

➄

No. Option

Description

➀

Diameter of the command device heads (Elan)

Diameter of the command device heads

(Elan or Elan + Siemens)

no command device mounted (empty enclosure

with 3 × mounting hole Ø 22.3 mm)

Special version (with the following special orde-

ring code)

➁

Command devices Elan

Command devices Siemens

➂

Mounting hole 22.3 mm

Mounting hole 30.5 mm

➃

NC and NO contact of the mushroom-shaped

pushbutton in separated form

Ergonomic pushbutton (with spring in the device

head) ADP55/3SW, actuating force 10.5 N,

1 NC + 1 NO

Ergonomic pushbutton (without spring in the

device head) ADP55/3SW o.F., actuating force

7.0 N, 1 NC + 1 NO

BWT-1

Complete kit sensor button A + B, output cable

2 m, incl. connecting cable, without two-hand

control panel

BWT-2

Complete kit sensor button A + B, output cable

5 m, incl. connecting cable, without two-hand

control panel

Not all component variants, which are possible according to this order

code, are available.

2.2 Ordering code operating push buttons (Elan)

EDP

➀

SW + EF03.1 + EF10.1

No. Option

Description

black, mounting diameter 22.3 mm, in combina-

tion with EF03.1 + EF10.1 switching elements

(1 NO + 1 NC, in separated form) or EF033.1 +

EF110.1 (2 NO + 2 NC, in separated form)

➀

Head diameter 42 mm

Head diameter 55 mm

ADP55/3SW

➀

+ RF03 + RF10

black, mounting diameter 22.3 mm, in combinati-

on with RF03 + RF10 switching elements

(1 NO + 1 NC, in separated form)

➀

without spring in the head

Not all component variants, which are possible according to this order

code, are available.

2.3 Ordering code contact elements for operating push buttons

(Elan)

➀

No. Option

Description

➀

NO element in combination with

EF10.1 switching element = 1 NO + 1 NC, in

separated form

033

NO element in combination with

EF10.1 switching element = 2 NO + 2 NC, in

separated form

NC element in combination with

EF03.1 switching element = 1 NO + 1 NC, in

separated form

➀

NO element in combination with

RF10 switching element = 1 NO + 1 NC, in

separated form

NC element in combination with

RF03 switching element = 1 NO + 1 NC, in

separated form

Not all component variants, which are possible according to this order

code, are available.

Summary of Contents for SEP 01.0







































Search results

Summary of Contents for SEP 01.0

Reviews:

Related manuals for SEP 01.0

Brands by name

Popular brands

schmersal SEP 01.0, Operating Instructions Manual

Search results

Summary of Contents for SEP 01.0

Reviews:

Related manuals for SEP 01.0

Brands by name

Popular brands