schmersal MZM 120 Operating Instructions Manual Download Page 8

8

Operating instructions

Safety switch with interlocking function

MZM 120

EN

Wiring example 1: Series-wiring of the MZM 120 safety switch with diagnostic output

The voltage is supplied at both safety inputs of the terminal safety component of the chain (considered from the safety-monitoring module).

The safety outputs of the first safety component are wired to the safety-monitoring module.

X1

Y1

X2

Y2

1

2

3

5

6

8

X1

X2

A1

A2

Y1

Y2

1

2

3

5

6

8

X1

4

Y1

4

Y1

X2

7

Y2

7

Y2

OUT

A1

A2

OUT

SPS/PLC

IN

SPS/PLC

SPS/PLC

IN

24 VDC

GND

SPS/PLC

n-participants max. 31 components in series

Safety outputs 

 evaluation

Wiring example 2: Series-wiring of the MZM 120 safety switch with serial diagnostic function

The safety outputs of the first safety component are wired to the safety-monitoring module. The serial Diagnostic Gateway is connected to the serial 

diagnostic input of the first safety component.

n-participants max. 31 components in series

Safety outputs 

 evaluation

Field bus

24 VDC

GND

1

2

3

5

4

6

8

X1

Y1

X2

SD IN

SD OUT

A1

A2

1

2

3

5

4

6

8

X1

Y1

X2

7

Y2

7

Y2

SD IN

SD OUT

A1

A2

X1

Y1

X2

Y2

SD IN

SD OUT

Y1

Y2

SD IN

9.2  Wiring configuration and connector accessories

Function safety switchgear

Pin configuration of 

the connector

Colour code or 

conductor numbering 

of the below-mentioned 

Schmersal connectors

Possible colour code of other  

commercially available connectors

with conventional 

diagnostic output

with serial diag-

nostic function

to EN 60947-5-2: 

2007

DIN 47100

A1

U

e

1

BN

1

BN

WH

X1 

Safety input 1

2

WH

2

WH

BN

A2

GND

3

BU

3

BU

gn

Y1 

Safety output 1

4

BK

4

BK

YE

OUT

Diagnostic output

SD output

5

GY

5

GY

GY

X2 

Safety input 2

6

VT

6

PK

PK

Y2 

Safety output 2

7

RD

7

VT

BU

IN 

Solenoid control

SD input

8

PK

8

OR

RD

Connector plug 

ST2 M12, 8-pole

Connecting cables with female connector 

IP67, M12, 8-pole - 8 x 0.23 mm²

Connecting cables with female connector 

IP69K, M12, 8-pole - 8 x 0.21 mm²

5

8

4

3

2

1

7

6

Cable length

Part number

Cable length

Part number

2.5 m

5.0 m

10.0 m

101209963

101209964

101209960

5.0 m

5.0 m

101210560

101210561 (angled)

Summary of Contents for MZM 120











Reviews: