manualshive.com logo in svg

Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX, Operating And Maintenance Instructions Manual, Page: 7 / 63

Share
Download
Schmalz SK-JU-110-2000-SRS63-3000-VSL-EX Operating And Maintenance Instructions Manual Download Page 7

 

 

SAFETY INSTRUCTIONS 

30.30.01.00226

/03 

www.schmalz.com 

EN   | 7 

1.2  Warnings 

Explanation of the warning symbols used in the operating and maintenance instructions. 
 

Icon 

Description 

Icon 

Description 

 

General warning symbol 

 

Explosive atmosphere 

 

Electrical voltage 

 

Flying debris  

 

Hand injury 

 

Crushing injury warning 

 

Suspended load 

 

Fall hazard 

 

Vacuum 

 

Hearing damage 

 

Warning of hot surfaces 

 

 

 

1.3  Mandatory symbols 

Explanation of the mandatory symbols used in the operating and maintenance instructions. 
 

Icon 

Description 

Icon 

Description 

 

Wear ear protectors 

 

Wear protective work shoes 

 

Wear protective gloves 

 

Disconnect mains plug 

 

Adhere to the operating instructions 

 

Wear eye protection 

 

 

Summary of Contents for SK-JU-110-2000-SRS63-3000-VSL-EX
































































Reviews:

No comments